Help ASAP  how can I determine the defletion at point a,b,c,d,e,f and g

Q: *3-44. Determine the magnitudes of F₁, F2, and F3 for equilibrium of the particle.

A:

Q: :For a thin wall cylinder, if the pressure is increased above certain limit then :Select one a. The…

A: For a thin walled cylinder if the pressure is increased above certain limit then,

Q: Which statement is true for the stress strain relationship for the metal shown? E B O Point D is the…

A:

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The composition of cast iron is 2.5 to 4 % carbon and 1-3 % silicon and the rest is iron. Cast iron…

Q: 0 W12X31 6-120 1.10m 4.20m 3.2n

A:

Q: Which rivet is least likely to fracture first? a A b C O B Ос d The rivets are equally likely to…

A:

Q: Write F if True and T if False. Marble and quartzite resemble each other in toughness and durability

A: Various mechanical properties required to define a material are: Hardness Toughness Durability…

Q: On examining a component which has failed by fatigue, the beach marks; O Radiate away from the…

A:

Q: Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi,…

A:

Q: A 1-in.-diameter steel circular rod is subject to a tensile load that reduces its cross-sectional…

A:

Q: The more the material is brittle, the higher angle of twist it exhibits before failure in twisting…

A: The given statement is false.

Q: A rectangular cross-section filleted bar with dimension D at its wide end and dimension d at its…

A: The problem is based on strength of material:

Q: An axially loaded member 600 mm long is carrying a tensile load of 40 kN. Its maximum stress is 100…

A: To find : The minimum area of body. Given :   The tensile load is P=40 KN The maximum stress is :…

Q: e the directions of reactions in the joints in the statec, please explain to me

A: The direction of the forces and moments acting on the connected objects must be an allowable…

Q: Find the force CD. The force is positive if in tension, negative if in compression.

A:

Q: le load it can take is (B) 33.48 KN

A:

Q: The 30 kN load is acting on the 4.25 cm´ area of the steel rod due to the stress…

A: Given data: A=4.25 cm2kt=2.1P=30 kN Need to determine the maximum stress.

Q: 4 F = 386,000 lb 36" LONG Stainless Steel Annealed 3870 rod F = 386,000 lb A = O= Will the rod fall?…

A: According to our guidelines, we are supposed to answer the first three sub parts. Please repost…

Q: e wrenches to ensure that a bolt has a prescribed on when used for connections. If a nut on the bolt…

A:

Q: wre of lenght and radLus tomm 200m Is Streached by 25.0omm on appueation F a force of tor the oYe…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

A:

Q: Choose all that apply. Tendency for a column to buckle is dependent on:     Shape of its corss…

A: The deformation caused on the member due to the application of compressive load beyond its critical…

Q: Find force member CE, FH, FG and HI by section method

A: The reaction forces are calculated as :…

Q: Load  applied tangentially across the resisting section is Select one: Buckling Tensile…

A: Shear Stress When two equal and opposite forces are applied tangentially across the resisting…

Q: 「十 a-6

A: Given:

Q: Please use method of joints to find the forces in members AB, AC, BC, BD, CD, and CE!!! Thank you!

A:

Q: Which of the following material can be produced by Silicon Dioxide .a Mild steel .b Elastomers .C…

A: (a) The only property shown by grey cast iron is brittleness.So, option (c) is the correct option.

Q: Qus - The state of two dimensional stress acting on a concrete lamina consists of a direct tensile…

A: Given data  State of stress  Normal stress = 6 MPa  Shear stress = 4 MPa  Find the maximum tensile…

Q: The type of joint used in wooden photo frarnes is O A. Mitre joint

A: Ans-A. Miter joint.

Q: F= 12,200 lbs. 875" 25 -- -Copper Annealed F= 12,200 lbs. ult A= O= Will it fail?

A:

Q: A 100 ma 100mm Thok 100mm mm ; 100 mm, A=200mm E = 2006 Pa find 200 KN As 400mm? Reactions с

A:

Q: 50 units 50 units A

A:

Q: Defien the formula used to Determine the flexural rigidity D of the mat ?

A: given; Defien the formula used to Determine the flexural rigidity D of the mat ?

Q: A The t a ef t e te en te Determine the following a. Shearing Stress in the head bolt. b. Shearing…

A:

Q: A bronze strip is securely fixed to a side of a steel strip of the same thickness, width and length.…

A: Given:Two strip are fixed together having same thickness, width and length.Young modulus of steel=…

Q: Choose all that apply. Tendency for a column to buckle is dependent on:     Shape of its corss…

A: This question is based on the concept of buckling of column.

Q: Plastic stage is when all elements of a steel section is in yielding condition and reaches its…

A: Stages in the loading curve of material are: Limit of proportionality PLastic stage Ultimate…

Q: Where is the maximum stress depending on ?the distance from the neutral axis إجابتك

A: Maximum stress  is on the outer most layer of beam  .In figure below, upper most layer has  maximum…

Q: Determine the vertical displacement of joint C . EA is constant

A: The vertical displacement of the joint C. FBD: The free-body diagram of the joint C is shown below.

Q: Among the two stress strain curves generated from tensile tests up to the material failure, which…

A: Given data:-stress strain curves of two different materials To find :-which curve, A or B represents…

Q: 1 Demi e ARCndD

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.