he three conductors of a 3-phase, 3-wire line are arranged at the corners of a triangle. which are 1 m, 1.3 m and 2 m. Calculate the inductance and capacitance per km of the line, when the conductors are transposed. The conductors are 1.5 cm diameter. [B.T.E. A.P. Power Systems II, T & D, June 1994) (Ans. 1.0923 mH: 0.0107 µF]

he three conductors of a 3-phase, 3-wire line are arranged at the corners of a triangle. which are 1 m, 1.3 m and 2 m. Calculate the inductance and capacitance per km of the line, when the conductors are transposed. The conductors are 1.5 cm diameter. [B.T.E. A.P. Power Systems II, T & D, June 1994) (Ans. 1.0923 mH: 0.0107 µF]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.26MCQ: Does r=e14r=0.788r, which comes in calculation of inductance, play a role in capacitance...

See similar textbooks

Related questions

Q: GMR calculate

A: Step 1:Step 2:Step 3:Step 4:

Q: Problem 6- A Three-phase 60 Hz transmission line has its conductors arranged in a triangular…

A: we need to find GMD and radius of conductor to calculate the required parameters.

Q: A single phase 2 conductor operates at 50Hz, the diameter of each condcutor is 60mm and spacing…

A: The inductance is expressed as the ratio of the flux linkage with the magnitude of the current. It…

Q: 2. A three-phase 60-hz transmission line has its conductors arranged in a triangular formation

Q: Compare the effect of varying resistance, capacitance and inductance in parallel and series AC…

A: Note: circuit compenets are not specified. we assume following AC circuits RLC parallel circuit RLC…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

The three conductors of a 3-phase, 3-wire line are arranged at the corners of a triangle, the sides of
which are 1 m, 1.3 m and 2 m. Calculate the inductance and capacitance per km of the line, when the
conductors are transposed. The conductors are 1.5 cm diameter.
[B.T.E. A.P. Power Systems II, T & D, June 1994)
(Ans. 1.0923 mH: 0.0107 µF]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

GMR calculate
I need the answer as soon as possible
For transferring electrical power at 220 kV, six conductors of ACSR Drake constitute a 60Hz double circuit three phase line arranged as shown below. The vertical spacing between consecutive conductors is 14ft; the longer horizontal distance is 32ft whereas the shorter horizontal distance is 25ft. a. Find the inductance per phase per mile and the inductive reactance per phase in ohms per mile. b. Find the capacitive reactance to neutral in ohm-miles. c. Find the resistance per phase per mile in ohms per miles. d. If the length of the line is 90 miles then draw an equivalent circuit of the line and analyse the open circuit and short circuit performance of the line. e. Find the maximum power we can transmit over the line. f. If the line is delivering power to a load of 20MW at 0.8 power factor lagging then find the voltage at the receiving end of the line. Also, Determine the voltage regulation, losses and efficiency of the line. g. If a fixed shunt compensation of 3 MVAr is attached at…
Please provide Handwritten answer
Solve it fast plz
Ans:32.4 kV I have the solution but didnt understand.Kindly explain the solution.
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
220 kV, 50 Hz, 200 km line has its conductors on the corners of a triangle with sides 6 m. 6 m and 12 m. The conductor radius is 1.81 cm. Find the capacitance per phase per km. [B.T.E. Pb. Elec. Power I December 1995) (Ans. 1.844 F) Into the