he tensile test is carried out on a steel rod of 16mm diameter and gauge lengthof 150mm.The yield strength of the steel is 700 MPa. At the tension load of 75 KN, Calculate stress ands train of the steel rod, taking Young’s Modulus of Elasticity as 200,000 MPa. Find out if the steel rod is in elastic region or already yielded.

Q: m

A: Applied tensile load = 330000 N = 330Kn Maximum Allowable Stress = 110 Mpa…

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data : Tensile load P=40 KN Change in length ∆L=0.0202 mm Initial length L=200 mm Diameter of…

Q: ven the stress-strain data from a tension test, how do you find the following : a) The modulus of…

A: Solution on below attachments

Q: A steel rod with a cross sectional area of 120 (mm] ^2 is stretched between two fixed points. The…

A:

Q: A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and…

A:

Q: A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to ten- sion, with the…

A: Given- gauge length=75mmd=19 mm

Q: Given: A steel rod (A= 150 mm2) is stretched between two fixed points with a tensile load of 5000 N…

A: Given data:A=150 mm2 Load,P=5000 Nα=11.7×10-6/°CE=200 GPa or 200×103 N/mm2

Q: A steel wire of 20 mm diameter is bent into a circular shape of 10 m radius. If E, the modulus of…

A:

Q: q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If…

A: Ans. b. 150 mm3

Q: 1.12 Tensile stress of 500MPA is applied on a steel rod of length 300mm. Determine the elongation in…

A: Given: Original length of rod, l = 300 mm Tensile stress, σ = 500 MPa Modulus of Elasticity, E = 200…

Q: steel having a diameter of 12.8 mm (0.505 in.) and a gauge length of 50.800 mm (2.000 in.) is pulled…

A: Given:-  A cylindrical specimen of stainless steel having a diameter of 12.8 mm (0.505 in.) and a…

Q: An aluminum alloy cylinder with a diameter of 76 mm and a height of 150 mm. is subjected to a…

A:

Q: A hot-rolled steel bar has a diameter of 12 mm was subjected to a tension test as shown in the…

A: NOTE  As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor…

A:

Q: A stepped steel shaft shown below is subjected to 10 N-m torque. If the modulus of rigidity is 80…

A: Given: A stepped steel shaft is given,Torque applied, T=10 N-mmodulus of rigidity, G=80 GPa

Q: The bending stresses on an element are: om 25,00 psi or= 21,667 psi. There is a stress raiser with…

A: Given:σm = 2500 psiσr   = 21667 psiSy  = 80000psiSu  = 90000 psiSe  = 40000 psiKf    = 1.4

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: A 2.0 m steel is being subjected into a tensile test. At force 30 kN, the length of the steel is now…

A: Given, Initial length of the steel subject (Li) = 2 m Length of steel after loading (LL) = 2.2 m…

Q: A steel rod with a cross-sectional area of 188 mm2 is stretched between two fixed points. The…

A:

Q: tion by the cross-sectional area. Is this approach t? To answer this question consider the loading

A: STress is the ratio of force to the cross -sectional area.

Q: Find the value of strain if stress is 40 N/mm2 and Youngs modulus is 70 N/mm2

A: Given data : The value of stress σ=40 N/mm2 The value of Youngs modulus E=70 N/mm2   Required :…

Q: The principal strains in a plane, measured cxperimentally, are c 630u and 6) 350u. It this is a case…

A:

Q: 30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected…

A: we have to determine the lateral strain

Q: (c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a…

A:

Q: (c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a…

A:

Q: Determine the strain if stress value is 33 MPa and modulus of elasticity is 80 MPa

A: Given data : The value of stress σ=33 MPa The value of modulus of elasticity E=80 MPa   To find :…

Q: AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS…

A:

Q: The inner and outer diameters of a hollow cylindrical steel are 10mm and 15mm, respectively. It is 1…

A:

Q: A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E= 200…

A:

Q: An aluminum alloy [E = 69 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P.…

A:

Q: Normal stress is calculated dividing the reaction by the cross-sectional area. Is this approach…

A: Given data in question  Normal stress approach To find out  Discuss the given statement

Q: A bar obtained by bonding together pieces of steel (E = 29 x 106 psi) and brass (E = 15 106 psi) has…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 psi M = 40 kip-in. This is a problem of Solid mechanics…

Q: A typlcal aluminum-alloy scuba diving tank Is shown. The outside diameter of the tank is 200 mm and…

A: Maximum shear stress in plane = pd/8t Where,  d = inner diameter  d = 200-2*12 = 176mm

Q: A high strength steel band saw of rectangular cross-section of size 20 x 0.8 mm thick runs over…

A:

Q: An applied torque results in a shear strain (y) of 3.75 x 10-3 in a solid circular steel shaft. At…

A:

Q: (c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a…

A: Given data in question  Stresses = 70 N/mm2 tensile and 50 N/mm2 Angle 40° To find out  Stresses on…

Q: Calculate the strain if initial length of rod is 104 mm and extension in rod due to tesnile load is…

A:

Q: A rod with a length of 1 m and a radius of 20 mm is made of high-strength steel. The rod is…

A: Solution: Given that : Length of rod = 1m = 1000mm Radius of rod = 20 mm Diameter of rod = 40 mm…

Q: calculate the lateral strain and the change in diameter.

A:

Q: 3. A new material is being developed and tested in the lab. The column was made using the new…

A: To find the elastic modulus and vicose coefficient

Q: For a given steel cube section subjected to three dimensional state of principal stress. 75 N/mm ☆J…

A: For steel cube,Yield stress=250N/mm2To find the factor of safety according to maximum strain energy…

Q: At an axial load of 24 kN, a 40-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.7 mm while…

A: