3. The maximum allowable value of T considering the given maximum permissible angle of twist for the entire shaft (express your answer inkNm):TkNm4. The corresponding maximum shear stress experienced by pipe KDQ and rod DQC considering the maximum allowable value of T (express youranswers in MPa):Тріре, таzMPaTrod,marMPa Consider the compound shaft KDQC which is composed of a 300 mm long solid rod DQC (G = 35 GPa) fitted snuggly (up to a length of200 mm) into a 600 mm (G = 63 GPa) long pipe KDQ. The rod has a diameter of 170 mm and the pipe has an outer diameter of 210 mmwith a wall thickness of 20 mm. Two concentrated torques are applied at Q and C with magnitudes and directions as shown. Note that the end Kof the pipe is fixed to a wall.ø210mm20mmC2.5TT400mm200100mmmmIf the maximum allowable twist at any section of the entire compound shaft is 0.0005 rad, determine the following:

Answered: Image /qna-images/answer/9e46c21e-564c-4c23-98fe-3e22a9490180.jpg

he maximum allowable value of T considering the given maximum permissible angle of twist for the entire shaft (express your answer in m): kNm he corresponding maximum shear stress experienced by pipe KDQ and rod DQC considering the maximum allowable value of T (express your wers in MPa): e,mar MPa mar MPa

he maximum allowable value of T considering the given maximum permissible angle of twist for the entire shaft (express your answer in m): kNm he corresponding maximum shear stress experienced by pipe KDQ and rod DQC considering the maximum allowable value of T (express your wers in MPa): e,mar MPa mar MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Single rivet lap joint is to commect 12 mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².
P7-L In cach case,calculate the value of Q and i that are used in the shear formula for finding the shear stress at A. Alsa, show how the shcar stress acts on a differential volume element located at point A. fa2m 02m tazm al aim (d) al m 03m 03 m taim Fozm le) a5m falm 402m 0.3m talm 01m (c)
Solve it
Need asap pls. Thanks.
Read the question carefully and give me right solution with clear calculations
A solid 1.00 in. diameter shaft is subjected to a torque of T = 240 lb-ft and an axial load of P = 5000 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 = i Tmax in-plane A i H (1) 요. 요.. psi psi T B psi P X (b) Show the stresses of part (a) and their directions on an appropriate sketch.
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 18 ksi, the normal stress in brass rod (2) must be limited to 23 ksi, and the normal stress in steel rod (3) must be limited to 14 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 6 kips, R = 16 kips and S = 23 kips. SI (1) VQ (2) (3) A Answer: F₁ = B R C D First: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A. i kips.
Class work: The two solid cylindrical steel rods AB and BC are welded together at B and loaded as shown in the figure. Knowing that the normal stress must not exceed 175MPa in rod AB and 150MPa in rod BC determine the smallest allowable values of d, and d₂. استنساخ 200 m مكتب المدير مقابل كلية الهندسة مجمع فاطمة 250 mm B 40 kN - d 30 kN
PROVIDE A CLEAR SOLUTION AND THE RIGHT ANSWER FOR THIS PROBLEM. PROVIDE INDIVIDUAL FBD
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths