QUESTION 1: THE GEAR DRIVEFigure 1 Example of a simple spur gear train with an idlerA simple spur gear train with an idler must transmit 650 W power. The pinion A isrotating at 92 rpm in an anticlockwise direction. Gear C has 45 teeth. Both the pinionand the idler are of the same size. Material proposed for pinion A and gear C is heavy-duty 817M40 steel, while for idler B is heavy-duty 655M13 Case hardened steel. 1.3 List four (4) types of gear trains.3Pag1.4 What is the purpose of the idler?

Answered: Image /qna-images/answer/1cf71c20-04bd-4251-b32f-629cc9c1a7d6.jpg

Answered: HE GEAR DRIVE C Figure 1 Example of a…

HE GEAR DRIVE C Figure 1 Example of a simple spur gear train with an ear train with an idler must transmit 650 W power. TI n in an anticlockwise direction. Gear C has 45 teeth. B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
Q1 Design a 4:1 spur-gear reduction for a 59 kW, three-phase squirrel-cage induction motor running at 1244 rev/min. The load is smooth, providing a reliability of 99.9 % at 109 revolutions of the pinion. Gearing space is meager. Use pinion materials to be Nitralloy 135M, grade 2 steel and nitrided through-hardened grade 1 steel material to keep the gear size small. The gears are heat-treated first then nitrided. Consider temperature factor is 1.1 for 250 0C.
design a spur gear drive for a motor running at 1500 rpm transmitting 15 kw power to a lower speed shaft with speed reduction ratio as 2.33:1. gears may bet aken as 20˚ full depth involute profile. Gear is made of grey cast Iron FG 200 and pinion of plain carbon steel 40C8. Assume starting torque to be 25% higher than the running torque.
The following data refer to two meshing involute gears of 20° pressure angle: Number of teeth on pinion 20, speed ratio = 2, speed of pinion = 250 rpm, module = 12 mm The addendum of each wheel is such that the path of approach and path of recess on each side are half of the maximum possible length. 1) Illustrate the value of addendum for both wheels, 2) Identify the length of arc of contact, and, 3) Formulate the free body diagrams for wheels in connection.
There is a motor with a power of 38 HP. The driving pinion has a speed of 20 rpm and the driven pinion of 5 rpm. Design the driving pinion and driven pinion based on the rpm of each pinion. do not forget the module and the number of teeth for each pinion. Gear ratio value: i= 5 rpm / 20 rpm = 0.25
Q2 A commercial enclosed gear drive is to be designed. Initially, the following is specified. The drive is to transmit 9.6 kW with an input pinion speed of 350 rev/min. The drive is to consist of two spur gears, with a 20° pressure angle, and the pinion is to have 20 teeth driving a 64-tooth gear. The pinion is made to be Grade 1 nitraded though hardened steel at 254 Brinell. The gear is made to be Grade 3 carburized and hardened steel at 284 Brinell. Both gears made to No. 6 quality standards. The gears will be uncrowned, centered on their shafts between bearings. A pinion life of 19232 cycles is desired, with a 99.99 per cent reliability. Analysis gears stress (bending and pitting) according to the AGMA approach and the corresponding factor of safety.
As shown in Figure 10-26, Please design a gear pair in the reducer of this belt conveyor. The input power is P=60 kW, the rotary speed of pinion is n1=960 r/min, the ration of teeth number is u= 2.5, the reducer is driven by electric motor. the design life is expected 10 years. the belt conveyor runs 12 hours per day. the load is stable.
22 The fellowtng data relate to a patr of 30 tmoiute gears m mesh: 3ochule - 6 mm, Number of terth on pinna - 17, Number of lorth on gear - 19, Adirnala on piniom and geur whoai -I modle Pind : 1 The mumber of pairs of teeth in cosact: 2. The angle nurned through by the pinion and the gaar wheel when one patr of teath is m contact, anmd 3. The ratio of sladteg to rolimg motton when the mp of a tooth on the larger whoel fi s Just mZkteg contact, fi ta jast leaving contact wate tz mating tooth, and ) is at the ptch pont.
An uncrowned straight-bevel pinion has 20 teeth, a diametral pitch of 20 teeth, and a transmission accuracy number of 6. Both the pinion and gear are made of through-hardened steel with a Brinell hardness of 300. The driven gear has 60 teeth. The gear set has a life goal of 10° revolutions of the pinion with a reliability of 0.999. The shaft angle is 900; the pinion speed is 900 rev/min. The face width is 32 mm, and the normal pressure angle is 20°. The pinion is mounted outboard of its bearings, and the gear is straddle-mounted. Based on the AGMA bending strength, what is the power rating of the gear set? Use Ko = 1, SF = 1, and SH = 1. %3D
None
A 14 teeth pinion gear drove a 40 tooth gear and stalled with a peak 376.1g being lifted from the scale. What was the torque at the motor shaft when this occurred? (The output pulley had a diameter of 1.25”)
Q12:- The figure below shows an epicyclic gear train. Pinion A has 15 teeth and is rigidly fixed to the motor shaft. The wheel B has 20 teeth and gears with A and also with the annular fixed wheel D. Pinion C has 15 teeth and is integral with wheel B (B and C being a compound gear wheel ). Gear C meshes with the annular wheel E, which is keyed to the machine shaft. The arm rotates about the same shaft on which A is fixed and carries the compound wheel B,C. If the motor runs at 1000 rpm, find the speed of the machine shaft. Also find the torque exerted on the machine shaft, if the motor develops a torque of 10 kg.m.