The angle strut is welded to the end C of the I-beam and supports the 1.3-kN vertical force. Draw the shear and moment diagrams for beam ABC. Then answer the questions. The distance x is measured from point A to the right.1.3 kN190 mmBAIC460 mm530 mmQuestions:At x = 110 mm, V =kN, M =kN.mAt x = 600 mm, V =kN, M =kN.mAt x =910 mm, V =kN, M =kN.mThe maximum (absolute value) shear force in beam ABC iskNThe maximum (absolute value) bending moment in beam ABC iskN•mBetween points A and C, the bending moment is zero at x =mm

givenexternal force applied =1.3KN=1300Nexternal force applied at a distance d=190mm=0.19m from the…

he angle strut is welded to the end C of the I-beam and supports the 1.3-kN vertical force. Draw the shear and moment diagrams for beam ABC. Then answer the questions. The distance x is measured from point A to the right. 1.3 kN 190 mm B 460 mm 530 mm Questions: t x = 110 mm, V = kN, M = kN-m t x = 600 mm, V = kN, M = kN-m t x = 910 mm, V= kN, M = kN-m he maximum (absolute value) shear force in beam ABC is kN

he angle strut is welded to the end C of the I-beam and supports the 1.3-kN vertical force. Draw the shear and moment diagrams for beam ABC. Then answer the questions. The distance x is measured from point A to the right. 1.3 kN 190 mm B 460 mm 530 mm Questions: t x = 110 mm, V = kN, M = kN-m t x = 600 mm, V = kN, M = kN-m t x = 910 mm, V= kN, M = kN-m he maximum (absolute value) shear force in beam ABC is kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refer the figure shown. 112 kN/m 112 kN/m 9 kN/m t1.50 m+ m- .50 2 m- Which of the following gives the maximum moment? Select the correct response 48 kN.m 84 kN.m 24 kN.m 42 kN.m
1. Given the following shear diagram. a. Sketch the beam showing the loading. b. Sketch the Moment diagram. V [16] 170 2' -70 -170 2' 240 2²
A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated by 4.3 m and P3=142 kN at 7.6 m from P2. Determine the beam dimensions if the maximum flexural stress is equal to 100 MPa. Use the ratio h = 1.6b. Round your answer into the nearest whole number. O 213 mm x 415 mm O 415 mm x 213 mm O 321 mm x 514 mm O 514 mm x 312 mm
w2 w1 Determine the shear force and bending moment in the beam. Use wl = 4 kN/m, w2 = 7 kN/m, a = 4 m, and b =4 m. The shear force at the point B of the beam in kN is (round to the nearest integer): kN The bending moment at the point A of the beam in kN.m is (round to the nearest integer): kN.m The bending moment at the point B of the beam in kN.m is (round to the nearest integer): kN.m The bending moment at the point C of the beam in kN.m is (round to the nearest integer): kN.m The location of the maximum bending moment from the point A of the beam in meter is (round to the nearest integer): meter The maximum bending moment of the beam in kN.m is (round to the nearest integer): kN.m
Determine the magnitude of resultant normal force N, Shear force V, and moment M across point D and point E
for final answer please round off to 2 decimal places for thumbs up!
slove f
the it For the given cross-section, if the width b = 6.6 in., the height h = 8.4 in., and the internal bending moment M = 132 kip-in. is applied as shown, at angle = 35° with the z-axis. Determine the absolute maximum bending stress (in the unit of ksi) at this cross section. M Ө ·b. с h Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point.
The cantilever beam is subjected to a uniform distributed load (g) and a concentrated force (F), at the locations shown below. Place the coordinate system origin (x = 0) at the left end of the beam, and follow the (ä standard sign convention for V and M from the textbook. Given: • L₁ = 1 m • L₂ = 4 m • F = 6 kN • q = 4.5 kN/m L₁ X q L₂ L₁ F
In the figure shown, the aluminum strut has a cross-sectional area in the form of a cross. If it is subjected to the moment M= 8 kN.m: 1) determine the bending stress acting at points A and B, 2) show the results acting on a stress distribution diagram.
Draw the Shear force and Bending moment for the Following then determine the maximum moment and the contraflexure position point. 2 kN/m 2KN с RA 4m d =10 B $ R₁ = 4 2m Ч
Draw the axial,shear and moment diagram for the given frame. Final answer must be rounded to nearest 3 decimal.