has a mass of 75 kg. 6-90 The plate shown in Fig. The brackets at supports A and B exert only force reactions on the plate. Each of the brackets can resist a force along the axis of pins in one direction only. Determine the reac- tions at supports A and B and the tension in the cable. GOD 1.2 m B 30° 1.4 m 2 m

Q: The light right-angle boom which supports the 260-kg cylinder is supported by three cables and a…

A: The mass of cylinder is m=260 kg

Q: 6F. The homogenous plate ABCD is supported by hinges along its side AB and by the cable ED.…

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: a=(3.7m) , b=(3.7m) ,theta =(33) , p1=(3.7)KN , p2=(2.4)KN     find the forces in each members…

A: According to the given dataWe need to findforce in each member.

Q: The uniform rod weighs 420LBa an has its center of gravity at G. Determine the tension in the cable…

A: Givenw=420LBa

Q: Determine the unknown forces by applying d’alemberts principle to a free body.

A: Even in the course of Fundamentals of Dynamics and Kinematics of machines, this principle helps in…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

A: Find the force in member AB , BH and BG  Where BF and CG are tension member.

Q: A wire is stretched tight between two pylons, one of which is shown in Fig. to the xy-plane and…

A: Draw the free-body diagram for joint D.

Q: The rigid body is supported by a hinge at A and a cable at C. The hinge resists 5.5m translation in…

A: Given data: The concentrated force acting at the center of the body is F = 260 N.

Q: The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A: To find the internal forces in members AB, BD, BC, and CD of the truss, we can analyze the forces…

Q: The smooth uniform rod AB is supported by a ball-and-socket joint at A, the wall at B, and cable BC.…

A: Given:The mass of the uniform rod is, .The acceleration due to gravity is, .Tension in cable BC is,…

Q: For the shown frame structure, the uniform beam AB weighs 480 lb and the uniform column CF weighs…

A:

Q: m The hoist supports an engine Determine magnitude of the force created by the engine mass

A: tanθ1=a+ba-btanθ1=2.2+1.12.2-1.1θ1=71.56o∑Fv=0RA+RB-mg=0RA+RB=mgRA+RB=175×9.81RA+RB=1716.75 N ,…

Q: Determine the force in each member of the truss shown in the figure below. 600 lb 600 lb 600 lb D…

A:

Q: bearings C and D) as shown below. Determine the tension in cable AB and the support reactions at…

A:

Q: determine the magnitude of the resultant force ( in SI Unit ) acting on the bracket and its F;= 300…

A: Given, ϕ=400F1=150 N Let the force F2 makes an angle α with the horizontal Therefore sinα=35cosα=45…

Q: 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force…

A: The force applied to the handle is, P=100 N Length of the handle is, L=30 cm

Q: 8. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

A:

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

A:

Q: The truss shown is used to support a 9 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A:

Q: SITUATION. The suspended load exerts a force F-800lbs at A and bar OA weighs 300 lb. Assume that the…

A:

Q: One of the smooth vertical walls supporting end Bof the 235-kg uniform shaft is turned througha 30°…

A: