has 2.0TPI. It is to lift 15 tons. The friction radius of the collar is 1-in. The coefficient of friction between the threads and s

Q: The single-threaded screw of the floor jack has a pitch of 15mm and a mean radius of 52.5 mm. The…

A:

Q: Determine the force required to raise a load of 3100 lbs., when a 2.5 in. triple threaded square…

A:

Q: 8. A ladder leans against a wall at an angle 0 with the wall. The top of the ladder is round and…

A:

Q: A turnbuckle, which is used to adjust tension in cables, is subjected to tension T=184.7 N as shown.…

A: Given data: The tension in the cable, T = 184.7 N. The lead of screw, L = 0.005 m. The nominal…

Q: An ACME-thread power screw is considered. The coefficient of friction of the thread is mu. The…

A: Given: The major diameter, d = 1.75 in The screw lead, l = 0.25 in The coefficient of friction, µ =…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: (a) A body of weight 55 N is placed on a rough horizontal plane. To just move the body on the…

A:

Q: An arrangement of three boxes is shown in figure below. Box A weighs 25 N and rests on an inclined…

A:

Q: A double-threaded power screw is used to raise a load of 5 kN. The nominal diameter is 60 mm and…

A:

Q: (11) Find the power required to drive a power screw lifting a load of 40001b. A 2½-in double square…

A:

Q: (a) A body of weight 55 N is placed on a rough horizontal plane. To just move the body on the…

A:

Q: (2) A single square thread jackscrew has 2.0TPI. It is to lift 15 tons. The friction radius of the…

A: Given data Thread : Single square thread with 2 Threads per square inch.   Friction radius of the…

Q: * 1. The light bar is used to support the m kg block in its vertical guides. If the coefficient of…

A: (a) Draw the free-body diagram of the block. Apply force equilibrium in vertical direction.…

Q: B) A body is pulled by a rope which passes 3 times round a power-driven capstan 600 mm diameter,…

A:

Q: M8x1 SAE 9.8 Bolts A B C P 100 D E F. 150 H I 100 100--100-80 400 A bracket is bolted onto a channel…

A: Given Bolt diameter = 8 mm To find Maximum load For bolt A, C, G, I For all the bolts Verify does…

Q: The screw jack of Fig. screw having a coefficient of friction of 0.35 and a mean ra- dius of 1 in.…

A: Write the formula for the angle of friction. The lead is maximum when the lead angle is maximum.…

Q: 1- The tightening and loosening torques. Is it self-locking? 2- Thread screw and nut induced…

A: P =331.7lb D=1 inch coefficient of friction (K) =0.2135 for 1030 hot rolled carbon steel tensile…

Q: A cylinder with a nominal 45 mm ID, a 60 mm OD, and a 30 mm length is to be mated with a solid shaft…

A: Cylinder nominal diameter, Length of the shaft Yield stress, Young's modulus, Coefficient of…

Q: 1. A single-threaded 25-mm power screw is 25-mm in diameter with a pitch of 5mm. A vertical load on…

A:

Q: 5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for…

A:

Q: ghtening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque requi

A: given:tightening force =2200NPitch=4mm

Q: In the figure, if the angle of friction is 10° at illustrate all surfaces in contact. Determine the…

A: given; friction angle(θ)=100lets take normal reaction between block=Nangle(α)=?upper block A…

Q: the bolt is 60 mm. with bolt The friction coefficient between the nut and bolt and the handle is…

A:

Q: In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded…

A: P =331.7lb D=1 inch coefficient of friction (K) =0.2135 for 1030 hot rolled carbon steel tensile…

Q: 3. What is the minimum static coefficient of friction required to maintain the bracket (light…

A: Consider the free-body diagram for the system as shown below.

Q: • Q3:An exhaust fan fitted with 900 mm diameter pulley is driven by a flat belt from a 30 kW, 950…

A: To findDetermine the necessary thickness of the belt and its total length.Giventhe diameter of the…

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a 2.9 ft, b-2.4ft, r - 6 in. "" W…

A:

Q: A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in…

A: The force on the shaft is 94236.5 N.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The…

A:

Q: the 31mm diameter screw has a double square theread with pitch of 6 mm and a lead of 12 mm .the…

A:

Q: An axial load of 160 lb is applied to the end bear- Fig. ses place over an annular ring of radius 4…

A: Given that, Axial load applied, P=160 lb,Inner radius of ring, r=4 in,Outer radius of ring, R=7…

Q: ind the work to be done in drawing the coaches together a distance of 200 mm against a steady load…

A: Pitch, P=10 mm=0.01 m,Mean Diamter, D=30 mm=0.03 mThreads are single start type,Coefficient of…

Q: Q2) design a nut, and screw jack (normal series) manufactured from a high grad materials and…

A:

Q: 4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm…

A: Given: Diameter, dw=4 mmouter diameter, OD=32 mmnumber of turns, Nb=3.5design factor, ns=Syσs=1.1

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

A:

Q: the bolt is

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.