(2) A single square thread jackscrew has 2.0TPI. It is to lift 15 tons. The friction radius of the collar is 1-in. The coefficient of friction between the threads and screws and base is 0.15, that between the screw and collar is 0.13. Determine: (a) the diameter of the root of the screw if the allowable stress in compression is 6,000psi; (b) the pull required at the end of 5.0ft bar to raise the load; (c) the twisting moment exerted at the root of the threads; (d) the efficiency of the screw and collar.

(2) A single square thread jackscrew has 2.0TPI. It is to lift 15 tons. The friction radius of the collar is 1-in. The coefficient of friction between the threads and screws and base is 0.15, that between the screw and collar is 0.13. Determine: (a) the diameter of the root of the screw if the allowable stress in compression is 6,000psi; (b) the pull required at the end of 5.0ft bar to raise the load; (c) the twisting moment exerted at the root of the threads; (d) the efficiency of the screw and collar.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The clamp of the given figure is used to hold a cover in place. The screw of the clamp has a single thread with a mean radius of 0.20 in and a pitch of 0.08 in. The coefficient of friction is 0.45, and the required clamping force is 100 lb. (a) Determine the twisting moment to tighten the clamp and (b) determine the twisting moment to loosen the clamp.
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.
Q.1 Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are 6. The permissible tensile stress for the bolt material is 90 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
Can I see your solution here and Answer I double check my work if its same answer. Thank you
An axial load of 160 lb is applied to the end bear- Fig. ses place over an annular ring of radius 4 in. to 7 in. :oefficient of friction of 0.20, determine the torque I to rotate the shaft for Contact between the end bearing and the A new bearing surface. 7 in. 4 in. 160 lb M
Please solve this question in hand writing step by step.
A single-threaded 25-mm power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency, and the torque to “raise” and “lower” the load. If the effort load is 75 N, find the force ratio and movement ratio.
A threaded machine bolt of 3/4 in diameter is screwed up tightly, fastening together two steel parts. To avoid the failure of the bolt in shear, the unit shearing stress must not exceed the elastic limit stress of 36000 psi. What maximum pull may safely be exerted on a wrench with a 20 in. moment arm to avoid failure on the root area if its root diameter is 0.6688 in. and if we assume that friction under the bolt head nullifies 25 percent of the pull
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.