H.W/A 300 m ring distributor has loads as shown in Figure below, where distanceare in meters. The resistance of each conductor is 0-2 per 1000 meters and thloads are tapped off at points B, C and D as shown. If the distributor is fed at A240 V, find voltages at B, C and D.نفسي50 A70D90لذلك240 VAC60B70 A680233'2 V100 A= BAجیل

Answered: Image /qna-images/answer/59ba2012-0aec-447b-a1d1-00cbb388fbaf.jpg

H.W/A 300 m ring distributor has loads as shown in Figure below, where distanc are in meters. The resistance of each conductor is 0.22 per 1000 meters and loads are tapped off at points B, C and D as shown. If the distributor is fed at 240 V, find voltages at B, C and D. 50 A 70 D 90 240 V A C 60 B 70 A 003 80 100 A

H.W/A 300 m ring distributor has loads as shown in Figure below, where distanc are in meters. The resistance of each conductor is 0.22 per 1000 meters and loads are tapped off at points B, C and D as shown. If the distributor is fed at 240 V, find voltages at B, C and D. 50 A 70 D 90 240 V A C 60 B 70 A 003 80 100 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. Identify the electronic symbol pointed by the line in the given schematic diagram F A TIP2066 with Heat Sink MA 01 Ohm E Sw TIP2055 wih Heat Sink B 10 Amp 50 PN Bridge Rectiter 0.1 Ohm SW LMTar2 we Heat Sink FUSE A FUSE 10A 230 Voit AC 12V Out o Gnd in 0.1 Ohm Sw 470uF 230112V 10A Transformer 47000UF Sov Output 10 uf 12V10A D A В C D F M CnolIL Choclk
The ohmic resistance of a large magnetic contractor is measured to be 25 ohms. A 200V is impressed on the contractor and the current is taken as 5A. Determine the inductance in mH and the reactive power of the load. The frequency is 60 HZ
If the core of LVDT is at the middle, then the output voltage will be a. maximum b. minimum c. Output voltage is no relation with core position d. 0
A Buck Converter converts 24Vdc to 12Vdc with losses of 70W, and a load of 60Ohms. What is the current drawn from the power supply?
Is there a difference between the phase windings resistances, if so, what does it mean? Please explain.
Grounding methods in Power systems
b1- The given ferromagnetic core relative permeability is 800. Determine the total reluctance of the core. 35 cm 10 cm 20 cm 50 cm 15 cm 45 cm 15 cm 15 cm 10 cm
In the given circuit, if number of turns of coil is 125 and current is 2A, relative permeability of the core is 765 and mean length of core is 0.2m and cross section area of 0.01m2 , then the flux generated in the core is Select one: O a. 1.24mWb HO b. None of these O c.0.124mWb O d. 1.24 Wb
SOLVE STEP BY STEP IN DIGITAL FORMAT
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --