H.W.5: Determine the design moment strength of a rectangular concretesection reinforced with six no. 9 bars in two rows.Given : b305 mmde622 mm, total depth h= 686 mm, andreinforced with three no. 9 bars, fy = 414 MPa and f. = 27.58 MPa.6 # 9305 mm686 mm622 mm

The width of the beam is b=305 mm. The effective depth is dt=622 mm. The total depth is h=686 mm.…

H.W.5: Determine the design moment strength of a rectangular concrete section reinforced with six no. 9 bars in two rows. Given : b 305 mm 622 mm, total depth h= 686 mm, and reinforced with three no. 9 bars, fy = 414 MPa and f. = 27.58 MPa.

H.W.5: Determine the design moment strength of a rectangular concrete section reinforced with six no. 9 bars in two rows. Given : b 305 mm 622 mm, total depth h= 686 mm, and reinforced with three no. 9 bars, fy = 414 MPa and f. = 27.58 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION A: The floor system shown has the following applied loads. Super Imposed Dead Load = 2.00 kPa Live Load = 1.90 kPa Slab Thickness = 100.00 mm Weight of Concrete = 24 kN/m3 Self-Weight of the beam = 1.92 kN/m Material Specifications: f’c = 21.00 MPa fy = 345.00 MPa Steel Cover = 50.00 mm What is the maximum positive moment of beam BE, acting on the midspan? in kN-m What is the maximum steel ratio of the section located at the supports? What is the actual steel ratio of the beam section at the supports? What is the ultimate moment capacity of the beam at the supports? in kN-m What is the effective flange width at the midspan? in mm What is the height of the compression block of the section at midspan? in mm What is the ultimate moment capacity of the beam at the midspan? in kN-m What would be the height of the CHB that can be placed on beam BE? Assuming the weight of the blocks is 2.30 kN/m per meter height? in meters
Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in negative bending.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A 15 x 25 in. column is reinforced with four No. 9 (No. 29) bars, one in each corner as shown in Figure (a). The concrete cylinder strength is f. = 4000 psi and the steel yield strength is 60000 psi. Determine the axial load strength for zero eccentricity without subtraction of the concrete displaced by the steel, as well as with subtraction of the concrete displaced by the steel. E=0.003, E,-29000. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area 25" bar size size (soft) Ib (in) (mm) (in') (mm") 2.5" -2.5" 0.250 - % 6.35 0.05 32 0.375 = % 9.53 0.11 71 0.500 = 4 12.7 0.20 129 0.625 = % 15.9 0.31 200 0.750 = % 19.1 0.44 284 0.875 = % 222 0.60 387 1.000 = % 25.4 0.79 510 1.126 - % 28.7 1.00 645 1.270- 1% 32.3 1.27 819 No.6 0.167 0.249 3 No. 10 0.376 0.560 #4 No. 13 0.668 0.994 Pn #5 No. 16 1.043 1.552 15" No. 19 1.502 2.235 #7 No.22 2.044 3.042 #8 No 25 2 670 3.973 As No 29 3.400 5.060 A's #10 No 32 4.303 6.404 e varies #11 No.36 5.313 7.907 1.410- 35.8 1.56 1.006…
Show all solutions
H.W.5: Determine the design moment strength of a rectangular concrete section reinforced with six no. 9 bars in two rows. Given : b 305 mm, d 622 mm, total depth h- 686 mm, and reinforced with three no. 9 bars, fy = 414 MPa and f. = 27.58 MPa. 27 6 # 9 305 mm 686 mm 622 mm
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3-22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPа). fc' 3D 28 MPа a. determine the effective depth of the beam b. determine the depth of compression block C. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam %3D
Using IS 456