H.W.4 Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in Figure 2 . The glue to be used can safely provide a shear strength of 120 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 10,000 lb. Note that a gap of 0.5 in. is required between boards (1) and (2). ahien Shu (1) 0.5 in.- FIGURE 2

H.W.4 Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in Figure 2 . The glue to be used can safely provide a shear strength of 120 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 10,000 lb. Note that a gap of 0.5 in. is required between boards (1) and (2). ahien Shu (1) 0.5 in.- FIGURE 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please show complete details, FBD, and solutions. Thank you!
Problem 3: Find the design moment strength for the following section: f'e = 6000 psi hf=6" T a. Mn = fy =60 ksi Es = 29,000 ksi b = 24" 8" bw = 4" bw=4" k-ft A's = 2 in² As = 6.5 in² (total) d` = 1.5" d = 30" Strain Stress
Give me right solution a=5 b=5
Connections Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks with a 2" overlap. The glue can carry 125 psi in shear. The wood can carry an axial stress of 1000 psi. How much force P can the joint carry? Sketch and FBD P b a P
please help me to design a simple tensile structure for the exhibition space roof
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
A channel-section has the dimensions as shown. 3) Consider a cantilevered beam subjected to an end force P. Cr (a) if cross L = 100 cm ction in is used determine its normal stress 2 2ºM 8⁰m 2cm
A flexural member is fabricated from two flange plates 1/2in x 16in and a web plate 1/4in x 20in. The yield stress of the steel is 50 ksi. a. Compute the elastic section modulus S and the yield moment My with respect to the major principal axis. b. Compute the plastic section modulus Z and the plastic moment Mp with respect to the major principal axis.
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN
Name: Time you spent to solve the problem HW- 3 ID.: 'Dėtërminë thé forċés in all the members, and state if these memibers are in tension or compression. Use table to arrange your Cal&tlations, show the results on the truss ( if not your witf täke zerở)** 30 N 4m 3 т 15
Please solve for the value of P.
At a certain location of a plate girder of web size 1000 mm x 10 mm, a pair of bearing stiffeners100 mm x 5 mm is welded. The effective area of bearing stiffeners is (in mm?)