H.W.2 For the circuit shown, determine the feedback topology & determine Ave, Rif, Rof Is V₂ Rs SO www 1.2k 6-W Rfs REE th 3K ww 300 R 1.2K₁₂=501 -hir In Ibi Ig Ibt Vo Re www Thie R Io (4) Vo 3-hfe D Re REL tr B = let hie 1.1k D=1+AB 1b2 Ic1 RE2 RE2+Rf lo 1b2 lo Ib2 Ai=- X Ib2 Ic1 lb1 Is Rc1 Rc1+R' = -150, R' R'+hie Aif=41 Rif= Ic1 Ib1 Ib1 Is = -150 (Rs//Rc1//hie) D Hello expert, I want to calculate all the unknowns according to the given laws, step by step and a clear line, please ,Rof=Rc2xD

H.W.2 For the circuit shown, determine the feedback topology & determine Ave, Rif, Rof Is V₂ Rs SO www 1.2k 6-W Rfs REE th 3K ww 300 R 1.2K₁₂=501 -hir In Ibi Ig Ibt Vo Re www Thie R Io (4) Vo 3-hfe D Re REL tr B = let hie 1.1k D=1+AB 1b2 Ic1 RE2 RE2+Rf lo 1b2 lo Ib2 Ai=- X Ib2 Ic1 lb1 Is Rc1 Rc1+R' = -150, R' R'+hie Aif=41 Rif= Ic1 Ib1 Ib1 Is = -150 (Rs//Rc1//hie) D Hello expert, I want to calculate all the unknowns according to the given laws, step by step and a clear line, please ,Rof=Rc2xD

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. The circuit given below has ß-200 R₁=59.5kQ; R₂=14.88kQ;R3=1kQ and R4=0.1kQ, Identify the feedback type and configuration and calculate the following: Open loop gain (A), feedback factor ß and closed loop gain (Af). Vi Сс www www R₁ R₂ 5 V I R3 R4 www · www Cc HH Vo
COMMON EMITTER AMPLIFIER CIRCUIT Choose appropriate parameters for the CE amplifier circuit (shown in figure) with a sinusoidal input of amplitude equal to 6mV and a gain of 1.9. Find Vout Choose appropriate parameters and solve the above question.
consider a sinusoid input with a peak amplitude of 2 mV. If the amplification gain A1 = 500 and k-0.125, the error (E) and the amplitude of the output waveform Vout of the feedback network are: R2 (a) Select one: O a. none of these O b. E=0.031m and Vout= 15.75mV O c. E= 127m and Vout= 15.75 O d. E=127m and Vout= 1V
Q2 Calculate the voltage gain, output voltage, input impedance, and output impedance for the cascade amplifier of Figure. Ipss V, = -5 B = 450 = 18 +20 V 22 k2 0.5 uF 2.4 k 15 kQ 0.5uF ImV pss 0.05 uF 4.7 ka 3.3 M0 680 0 # 100 uF = 100 uF
Problem • Determine the input and output impedances of the given amplifier. The op-amp datasheet gives: Zin = 2 Mohm, Zout = 75 ohm, A = 200000. 4 Find the Closed-loop voltage gain. www R OV 220 ΚΩ R₁ 10 ΚΩ out
Q2) For the circuit shown in the figure, calculate the input resistance for each step and find the overall voltage gain in dB. Assume Bpc = 100 and Bac = 150 Vce +12 V Rc 2.2 k2 R 5.6 kfN R1 56 kN R4 22 k 330 E RE Vin o R2 12 k2 RE 1.0 kN
2. Determine VCE in the below transistor circuit. Assume that the transistor is in active mode, V BE = 0.7, VCE > 0.2 and B = 150. (1k = 10³) Enter your final answer in the below box VCE = 2V 100kn 200ΚΩ I kn VCE 16V
2. Non-linear feedback elements are quite common as we will observe later this semester. The non-linear circuit in the feedback network shown is called an analog multiplier. The terminal characteristics of the analog multiplier are defined as shown in the figure. Show that this circuit can be used an analog signal divider. That is derive Vo in terms of Vs1 and Vs2. R2 Multiplier Vs2 R1 Vs1 Va Multiplier V = KVa V6 11-1-1-110l 10I ..... ...... ... DID
CE Amp with pnp transistor VEE = 12V RE 13K2 prp B=l00 R2 look CE VA = O0 %3D Ri : G Rout (ka C2 RIN 300k2 Re RL Vo 43 k2 43k2 Find : 6) Av 6) RIN G) Rout d) max Vi to avoid small signal distortion ) max Vi to awidgoutput noltage ongadistarihim clipping in the
Determine Avs and AIs
A boost converter has an input voltage Vb=5V. The average load current is lo=0.5A. The switching frequency is 25 kHz. Suppose that a regulator is added (L=.15 mH and C=0.22 mF) and that the current is continuous. If the average output voltage is Vo =15V, then the critical values of L and C for the considered boost converter are equal to: Select one: O a. 0.133mH and 0.88UF O b.0.0665 mH and 0.44UF c. 0.133mH and 0.44UF d. None of these
R₁ www 22 k R www 150 ΚΩ (b) out (c) Refer to Figure (c). The closed-loop gain, ACL is R 582 ΚΩ PRO www R₂ 10 kn R 33k wwwwww R 12,7 ΚΩ