(b) An inverting amplifier circuit using Op-Amp 741 IC, a feedback resistor, RF and input resistance, RA = 5 kM is used in a feedback oscillator circuit. The output pin of the amplifier is connected to the three RC network that can generate frequency of oscillation, fo = 20 kHz. Assume that R1 = R2 = R3 =R and C = C2 = C3 = C. (i) Name the oscillator circuit. (ii) Draw the oscillator circuit. (ii) Using a capacitor value of 0.001 µF, determine all other component values.

(b) An inverting amplifier circuit using Op-Amp 741 IC, a feedback resistor, RF and input resistance, RA = 5 kM is used in a feedback oscillator circuit. The output pin of the amplifier is connected to the three RC network that can generate frequency of oscillation, fo = 20 kHz. Assume that R1 = R2 = R3 =R and C = C2 = C3 = C. (i) Name the oscillator circuit. (ii) Draw the oscillator circuit. (ii) Using a capacitor value of 0.001 µF, determine all other component values.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) For an opamp, the input bias current Ib =60uA and the input offset current lio= 10uA Find the input base currents and In b) Design an opamp circuit with the following output: Vo = - Vin/4 + 2 For the circuit given below Given :Vin-0.2V, Vsat= 12V D Identify (name) the circuit (stage 1 and 2) O Find the output voltage Vo and the current through the load 4ka 0 Find Vo if the resistor 2kn opens 10 k Stage Stage 2 Vo Vin
The midrange open-loop gain, "Aol(mid)" of a certain op-amp is 80,000. If the open-loop critical frequency is 1 kHz, what is the open-loop gain, "Aol" at each of the following frequencies? (a)100 Hz (b) 1 MHz
Suppose a small AC voltage of amplitude .1Vpp is added to the input voltage of 5V What is the output AC voltage and the small signal voltage gain? Vin Lo VDD=10V R=10 Q2 Vout
The operational amplifier (op-amp) in Figure 1 is an ideal op-amp with maximum output voltage, vO(max) is +12 V and the minimum output voltage, vO(min) is -12 V. A sine wave with ±5V peak-to-peak voltage is applied as the input, vin as shown. For each of the following conditions, derive or explain the relationship between output voltage, vo and input voltage, vin, and then draw the input and output voltage waveforms on same graph. Label the x-axis, y-axis, peak voltages and units. 1.R1 = R2 = R3 = 10 kΩ and RF = 3R1. 2.R2 = R3 = 10 kΩ, RF = 3R2 and R1 is broken (open circuit). 3.R1 = R2 = R3 = 10 kΩ and RF is broken (open circuit). 4.R1 = R2 = 10 kΩ, RF = 3R1, R3 is broken (open circuit) and the op-amp’sinverting and non-inverting terminals are accidently interchanged where node ‘x’ is connected to the non-inverting input while node ‘y’ is connected to the inverting input of the op-amp.
Q2) Draw a 16-bit digital to analog converter circuit and show if the reference voltage was (-20V) how much will be the output voltage if the digital input to the DAC is (1000 1100 0011 1111). Upload you answer here
draw the block diagram of op-Amp
For the op-amp shown in the following figure, the midrange voltage gain is equal to- Vo 3 kn Select one: Oa-26.7 Ob-27.7 c. 27.7 d. 26.7 80 kf m
An op-amp has an open-loop gain of 105 and an open-loop upper cutoff frequency of 10 Hz. If this op- amp is connected as an amplifier with a closed-loop gain of 100, then the new upper cutoff frequency is
Subject: Analog Electronic and Circuit Please Solve this question
An inverting op amp has Rf= 600kohm and R1= 6kohm. Determine the op amp circuit voltage gain, input resistance and output resistance. Also Determine the output voltage and input current if the input voltage is 0.1 V. Assume op amp to be ideal one.
(a) An instrumentation system shown in Figure Q3 (a-i) has a Nickel resistor detector device (RTD) sensor with the characteristics shown Figure Q3 (a-ii). The three wires bridge has R1= 200 Q, R2= 500 Q, and R3= 650 Q. The amplifier has a gain of 17.2, and the battery voltage is VB=1.2v. (i) Calculate the amplifier output voltage Vo when the boiler temperature is 150 °C. (ii) Explain the RTD principle of operation. R1 R2 Industrial boiler Nickel R3 RTD Vaa Vo Figure Q3 (a-i) 400 Nickel 350 300 Platinum 250 200 150 100 50 Copper -200 200 400 600 800 RTD temperature (oC) Figure Q3 (a-i) RTD Resistance ()
Q1: a) Design the oscillator in Figure 1 to start oscillation with R closed-loop gain of 8.5, then sustain oscillation at a resonant R1 o Vout frequency Assuming of 3.4 kHz. the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback R2 C2 resistance setting when R3 R4 C3 oscillation is stable? 1.0 kN Figure1