H.W 8What force is required to punch a 20-mm-diameter hole in a plate that is 25 mmthick? The shear strength is 350 MN/m².20 mm25 mm thickPuncher H아The resisting area is the shaded areaalong the perimeter and the shear forceV is equal to the punching force P.Punched out2025 mm

Given, Diameter of the hole, d = 20 mm = 20 × 10-3 m. Thickness, t = 25 mm = 25 × 10-3 m. Shear…

Answered: H.W 8 What force is required to punch a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please help solve and explain and include FBD please
Simple stress and strain problem:
Calculate the stress
What is the normal force distributed to Stainless Steel Solid Post 'A' (in kips)? What is the normal force distributed to Red Brass Hollow Tube 'B' (in kips)? What is the normal stress produced in Stainless Steel Solid Post 'A' (in psi)? What is the normal stress produced in Red Brass Hollow Tube 'B' (in psi)? INDICATRE FREE BODY DIAGRAM
If the ultimate shear strength of a steel plate is 42,000psi. What is the force necessary to puncha 0.75in diameter hole in a 0.625in thick plate
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
Learning Goal: To analyze two built-up members that have the same geometry but are fastened differently, determine the maximum applicable shear force on each cross section, and determine the adjustment in spacing between the weaker member's fasteners that would allow the member to support the equivalent maximum shear force of the stronger member. The two cross sections shown below, (a) and (b), are subjected to a vertical shear force as shown. The members are fastened by nails that can support a load of 22.00 kN each and are spaced perpendicularly to the page in increments of s = 125.0 mm. The geometries of the cross sections are given by a = 235.0 mm, b = 50.00 mm, c = 225.0 mm, d = 135 mm, and e = 275 mm. Assume the cross sections are uniform along the entire lengths of the members. bk (a) Part A - Maximum applicable shear force on the member (a) *ak b 17 b ➜bk ➜bk Determine the maximum applicable shear force on the member (a). Express your answer to four significant figures and…
Big and clear handwriting with all steps . Make sure calculations and answers are accurate please. THANK YOU
please write by hand
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2to 2 decimal places. (show all work)
Q6 A spherical vessel of 1.6m inner diameter is constructed by joining two hemispheres with equally spaced bolts as shown in fig.3. The vessel will operate at an internal pressure of 600kPa. Calculate the vessel plate thickness t. Given the allowable stress for the sphere plate will equal 50MPa. If the same plate was used to make a cylindrical vessel to operate at the same internal pressure, find the cylinder maximum allowable diameter. ... المزيد A Ľ تعديل حذف 0 المفضلة Lo مشاركة
Plates and rods are frequently used to help rehabilitate broken bones. Calculate the shear stress in the lower 5 mm diameter biomedical bolt if it is supporting a 1,200 N force from the bone. F (Express your answer using three significant figures.) |MPa

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

H.W 8 What force is required to punch a 20-mm-diameter hole in a plate that is 25 mm thick? The shear strength is 350 MN/m². 20 mm 25 mm thick Puncher H 아 The resisting area is the shaded area along the perimeter and the shear force V is equal to the punching force P. Punched out 20 25 mm