H.W 1 The bracket plate is 40 mm thick. b= 272 mm. Load on the bracket, P= 100 kN; spacing, C ( designed by yourself) mm; load arm, e 500 mm. Permissible shear stress is 60 MPa , crushing stress is 130 MPa, and the tensile stress in the material is not to exceed 88 MPa. Select one of the pattern below and Determine :1. the size of the rivet or bolt to be used for the joint. 2. Calculate the Efficiency of the joint, and which is the best pattern ? ( compare only two patterns )( Optional) 中中 |中中中中中中中 b + 中中中中中中中中中中中中中中中

H.W 1 The bracket plate is 40 mm thick. b= 272 mm. Load on the bracket, P= 100 kN; spacing, C ( designed by yourself) mm; load arm, e 500 mm. Permissible shear stress is 60 MPa , crushing stress is 130 MPa, and the tensile stress in the material is not to exceed 88 MPa. Select one of the pattern below and Determine :1. the size of the rivet or bolt to be used for the joint. 2. Calculate the Efficiency of the joint, and which is the best pattern ? ( compare only two patterns )( Optional) 中中 |中中中中中中中 b + 中中中中中中中中中中中中中中中

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2
Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN. Determine the smallest allowable outside diameter of the tube if the working stress is 110 MN/m2 Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each plankes if the working bearing stress for wood is 13 MPa. 20 mm
Kindly show the complete step-by-step solution and free body diagram. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you.
Please give the given, required, and the solution. Draw the free body diagram and label properly.
#3 handwritten then box the final answers
with an illustration all required section.
bearing stress show complete solution and provide the -given -required -FBD -formula and solution bearing stress show complete solution and provide the -given -required -FBD -formula and solution
4. Solve this with a clear solution to avoid confusion.
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
The lap joint shown is fastened by four 314" dia. bolts. Assume the applied load is uniformly distributed among four rivets. The width of plate is 5 inch with 1/2 inch thick and a tensile stress is 16 ksi. (assume that hole is greater than fasteners by 1/8") 00 a) What is the value of the external load "P" that the plate could carry? .b) What is the shear stress of the rivet? c) What is the bearing stress of the of the plate? .d) If the % bolt is replaced with 1" dia. bolt, what is the tensile stress of the of the plate? P.
2) A machine frame is made of steel having Sy = 400 MPa and Ssy = 250 MPa. When loaded in a test fixture, the stresses were found to vary linearly with load. Two points on the surface were found to be most critical. With a 4-kN test load, stresses at these points were: point a, 0₁ = 200 MPa, 0₂ = 100 MPa; point b, 0₁ = 150 MPa, 0₂ = -100 MPa. Compute the test load at which the frame will experience initial yielding according to the (a) maximum-normal-stress theory, (b) maximum-shear-stress theory, and (c) maximum-distortion-energy theory. Discuss briefly the relative validity of each theory for this application. Considering all the information available, what is your best judgment of the value of the test load at which yielding would actually be expected to begin? 02= 100 MPa a 02 02=-100 MPa b 02 0₁ = 200 MPa 01 = 150 MPa
Q1) Determine the size of the rivets to be used for the joint of the bracket shown in Figure (1). All rivets are to be of the same size. Rivet spacing C is 30 mm; plate thickness is 25 mm; permissible shear stress is 200 MPa and permissible crushing stress is 400 MPa. kukood + + + ACICH 300 mm Figure (1) 10 KN