Group 1Q1) Design with drawing a multi range Ammeter (directmethod) for the range 50mA, 100mA and 1A. Assuming that thefull scale galvanometer current=20mAand its internalresistance= 10KQ.Q2) A galvanometer with a full scale current =5mA and internalresistance=5KO is used to design a voltmeter. What is the rangeof a voltmeter if 10KQ is connected in series with thegalvanometer?

In 1st question, we have to design multirange ammeter with finding shunt resistances...In 2nd…

Group 1 Q1) Design with drawing a multi range Ammeter (direct method) for the range 50mA, 100mA and 1A. Assuming that the full scale galvanometer current=20mA and its internal resistance= 1OKQ. Q2) A galvanometer with a full scale current =5mA and internal resistance=5KO is used to design a voltmeter. What is the range of a voltmeter if 10KQ is connected in series with the galvanometer?

Group 1 Q1) Design with drawing a multi range Ammeter (direct method) for the range 50mA, 100mA and 1A. Assuming that the full scale galvanometer current=20mA and its internal resistance= 1OKQ. Q2) A galvanometer with a full scale current =5mA and internal resistance=5KO is used to design a voltmeter. What is the range of a voltmeter if 10KQ is connected in series with the galvanometer?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the operating voltage of the LED diode given in the circuit in the figure is 2.2V, the operating current is 30mA, and the Vs source voltage is 12V, calculate the value of the R1 resistor connected in series with the diode.
The diode starts to conduct when the voltage across it is 0.6 V. Vin is a variable DC voltage source. R1 = 12.2 Ω and R2 = 6.7 Ω. At what value of Vin in volts will the diode start to conduct if Vin is increased from zero.
According to the figures, the required load for the zener diode to regulate in the circuit is minimum how many ohms is its resistance?
For the Precision Rectifier in Figure 3, what is the output voltage equation during the Negative-Half Cycle using ideal diodes? choose the correct answer: 1)V0=0V 2)V0=-Vin 3)V subscript o equals negative R subscript 1 over R subscript 2 V subscript i n end subscript 4)V subscript o equals fraction numerator negative R subscript 2 over denominator R subscript 1 end fraction V subscript i n end subscript
In the circuit shown below, the diode has a turn-on voltage of 1 V. Assume Vs = 39V, R₁= 10k ohm and R₂= 5 k ohm. Assume the diode is 'on' and find the diode current in mA. Round your answer to two decimal places. V R₁ www 11₂ ww R₂ [13 4
The purpose of the Zener diode is to maintain the voltage across the load at 10 V. The maximum power required by the load is 5 W. If Vs = 17 V, what is the maximum value of R that can be used by the circuit? Express your answer in ohms accurate to two decimal places. + www R * LOAD
Solve for the following (Diode)
I need a detailed explanation of the process. Thank you.
Determine the range of values of Vi that will maintain the Zener diode in the “on” state. (SHOW COMPLETE SOLUTION)
Hi , I hope you can solve this question fast please ?
For the diode circuit of the figure below: 1. Determine v, and sketch its waveform for at least 4 cycles 2. Determine the average (dc) voltage established the load Show the details of your work. Without a complete solution (step-by-step solution) will invalidate your answer. 120 V 2.7 kN -120 V
AsP plzzzz