Given: • The members are a rectangular cross-section with a radius of 16 mm. • Thickness of each member is 14 mm • Diameter of the rivet used is 18 mm Determine: a. Cross-sectional area of the members b. Internal load in member AB, and indicate if 3 m 4 m tension or compression c. Internal load in member BD, and indicate if tension or compression d. Normal Stress in member AB e. Bearing stress in member BD 3m 50 KN 80 KN 4 m

Given: • The members are a rectangular cross-section with a radius of 16 mm. • Thickness of each member is 14 mm • Diameter of the rivet used is 18 mm Determine: a. Cross-sectional area of the members b. Internal load in member AB, and indicate if 3 m 4 m tension or compression c. Internal load in member BD, and indicate if tension or compression d. Normal Stress in member AB e. Bearing stress in member BD 3m 50 KN 80 KN 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the force in member CF in lbs. If P1 = 638 lbs and P2 = 842 lbs note: Negative value if…

A: To find force in member CF

Q: The signboard truss is designed to support a horizontal wind load of 640 lb. If the resultant of…

A: We have to determine the value of force in member BG and BF if the force are positive than tension…

Q: A square bar carries the series of loads as shown. Compute the load (kN) and stress (MPa) in each…

Q: Question 1. Determine the force in member BC, FC, FE and state whether the forces are in tension or…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: G 60 60° D 10 10' 20 10 10' 1200 lb 1200 lb 1200 ib 1200 ib Determine the internal force on: Member…

A: LAC = 40feet

Q: 1. Determine the force in members BC, HC, and HG. State if these members are in tension or…

A: Given: A simply supported truss with hinge at support A and roller at support E. To find: Forces in…

Q: PROBLEM 2 Determine the forces in members GB, GF, GC and BF by the: a). Method of Joints b). Method…

A: Given:-The above truss loading is shown. To find-Force in members GB, GF, GC, and BF by using the…

Q: Fer = Value Units Suppose that P = 5 kN and P, = 10 kN (Eigure 1) %3D Submit Request Answer Part B…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: 2.19 The rigid bar ABC is supported by a F the largest vertical load P that can be applie limited to…

Q: • Part A Suppose that P = 12 kN and P = 17 kN. (Figure 1) Determine the force in member CF of the…

A: Away from the joint : tension (+ve) Towards the joint : compression (-ve)

Q: DIRECTION: Solve and Analyze the following problems in neat and orderly manner. All problem…

Q: - FIND REACTIONS -DRAW SHEAR PIAGRAM - DRAW MOMENT PIAGRAM Wz= 0.5k 6' 121 V-o VMAX %3D Mmax = MMAX=…

Q: A bike brake consists of two pieces AOB and COD (Fig.P3.17). Draw the associated FBD for structural…

A: The piece AOB of the bike brake has the following elements. Internal hinged support at Point O.…

Q: Provide the information missing (blanks) in the table ONLY for caiculate COMPOSITE centroid of the H…

A: Dimensions of B = 0.1 m*(2*0.7)m Dimensions of B = 0.1 m*1.4m Area of A = 0.1 *0.7 =0.07 m2 Area of…

Q: Determine the force in the following members. Indicate if T or C. Express your answers in three…

Q: Suppose that P₁ = 33 kip, P₂ = 22 kip, and P3 = 11 kip. (Figure 1) Figure 40 ft- -40 ft- -40 ft- D…

Q: Determine: a. Cross-sectional area of the members b. Internal load in member AB, and indicate if…

Q: Problem 2.19 (Ans. f. = 1223 psi: f. = 30,185 psi at the steel centroid) %3! 3 in. 15을 im. M = 120…

A: Flexural strength indicates the strength of concrete beams and slabs under tensile loads.…

Q: 3.) Determine the forces in each member and determine if each member is in compression or in…

Q: Define the following a) Flexure stress b) Flexural rigidity c) Neutral axis/surface

A: When a beam is subjected to bending moment it sags or hogs. When it sags fibres at the bottom are…

Q: Draw the FDBS of member ADB and BEC

A: For the given frame, The free-body diagrams of the member ADB and BEC have to be drawn

Q: 2-16. A truss is loaded as shown in Fig. P 2-15. Determine the resultant load on the truss. 5000…

Q: 3. Find the member forces in members KJ, KD, CD and JD, specify whether they are in tension or…

Q: Given that the diameter of all members cross-section is 32 mm. Determine the stress in member BD,CD…

Q: Suppose that P-320 lb (au1) Figure Figure Ⓒ1of1 > ▾ Part A Determine the force in the membe Express…

Q: EXAMPLE 4.5.1 Determine the force in cach member of the truss shown in the Fig. 4.5.5 and indicate…

Q: 4. The joint is fastened together using two bolts. The diameter of each bolt is 13.5 mm. Determine…

A: Given data in question Load 80 kN Diameter 13.5 mm Width 30 mm Number of bolts 2 To find out…

Q: xpress the tensions or compressions in the bars AB, AC and AD as a function of L

A: A structure is given belowneed to find member forces in AB,AC,and AD as a function of L

Q: Sassssss Q2: Determine approximately the force in 5 kN 10 kN 5 kN H diagonal members DH and CG of…

A: We have to find the value of approximate force in diagonal member DH and CG of the truss shown in…

Q: B 4.5m 主 P2 3. 4m 1.5 m 2.8nH.5m Find the forces in all members of the muss Shown in the figure ·…

Q: III – Stress Analysis of Trusses 3. Determine the forces CE, DF & FG of the truss using method of…

Q: Determine the force in member BC and indicate if tensile or compressive. 1 kN 1 kN 1 kN 1 kN 1 kN 2…

A: Given, A truss,

Q: Determine the force in each member of the truss shown in Fig. 4.20(a) by the method of joints.

A: Support reaction : ∑MB=0RAY×5-30×5+25×12+50×6=0RAY=-90 KN∑FY=0RAY+RB-30=0-90 +RB-30=0RB=120…

Q: Determine CF, CE bar forces and indicate whether it’s tension and compression.

A: To determine the value of forces in members we will be using method of joints. In this method, each…

Q: Strain energy for truss AC. Enter your answer in J to 2 decimal places. Positive value indicates…

Q: HW4: - The Inverted T section of a L-m simply supported beam has the properties shown in Fig. (4).…

Q: 3m 3m 3m [Tu A 1.5 1.5 E 1.5m D← B 900 N 18 N + 900 19 A = 800 mm ² Read: Member Stresses in F6, 6C,…

Q: Find the internal force in the truss member EB. EB = KN, Compression O 3.75 10 kN B O 11.35 4 m O…

Q: a plate subjected to loads. Replace the loads by an equivalent force through C and a couple acting A…

A: Consider the figure,

Question

Determine:
a. Cross-sectional area of the members
b. Internal load in member AB, and indicate if
tension or compression
c. Internal load in member BD, and indicate if
tension or compression
d. Normal Stress in member AB
e. Bearing stress in member BD

Given:
• The members are a rectangular cross-section with a radius of 16 mm.
• Thickness of each member is 14 mm|
• Diameter of the rivet used is 18 mm
Determine:
a. Cross-sectional area of the members
b. Internal load in member AB, and indicate if
3 m
tension or compression
c. Internal load in member BD, and indicate if
tension or compression
d. Normal Stress in member AB
4 m
E
3 m
C
80 KN
4m
50 KN
e. Bearing stress in member BD

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

PLEASE ANSWER IN 20 MINS
3. Find the member forces in members KJ, KD, CD and JD, specify whether they are in tension or compression. K L H A B 4 kN 4 kN 6 kN 6 kN 8 kN 6 @ 0.8 m 1.8 m 3.6 m 4.8 m
Determine the following:a. Cross-sectional area of the membersb. Internal load in member AB, and indicate iftension or compressionc. Internal load in member BD, and indicate iftension or compressiond. Normal Stress in member ABe. Bearing stress in member BD
3. Find the member forces in members KI, KD, CD and JD, specify whether they are in tension or compression. K L H A B E F 4 kN 6 kN 6 kN 4 kN 8 kN 6 @ 0.8 m
6
Complete solution pls. Tysm!
Determine the reactions at the supports. First, determine the equivalent load [kN] as required below and provide the location of each one from A [m]. The distributed load equivalents MUST be ONLY 2. One for the triangular distribution (FR1) and the other for the rectangular distribution (FR2). 6 kN/m Scale: 1 unit = 0.5 m FR1- FR2- Reaction1 (if present – specify [ Reaction2 (if present – specify [ {kN]; Location from A =, {kN]; Location from A = 1), at A = 1), at A = m [kN] [kN] Reaction1 (if present – specify [ Reaction2 (if present – specify [ 1), at B = 1), at B = [kN] [kN]
This a mechanics of material question please show all steps so your approach is easily followed. Please show Free body diagram, what is given, and what the problem is asking for. Thank you
Need answer please ASAP ty!
2.)Determine the forces in each member and determine if each member is in compression or in tension.