* Determine the reactions at the supports. First, determine the equivalent load [kN] as required below and provide the location of each one from A [m]. The distributed load equivalents MUST be ONLY 2. One for the trianqular distribution (FR1) and the other for the rectangular distribution (FR2). 6 kN/m Scale: 1 unit = 0.5 m

* Determine the reactions at the supports. First, determine the equivalent load [kN] as required below and provide the location of each one from A [m]. The distributed load equivalents MUST be ONLY 2. One for the trianqular distribution (FR1) and the other for the rectangular distribution (FR2). 6 kN/m Scale: 1 unit = 0.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three rods. Rods (1) and (2) are 16-mm- diameter stainless steel rods that have an elastic modulus of E= 185 GPa. Rod (3) is a 23-mm-diameter bronze rod that has an elastic modulus of E= 100 GPa. Use a = 1.4 m and L = 2.6 m. For a load magnitude of w = 30 kN/m, calculate (a) the normal stress in each rod. (b) the vertical deflection of the rigid bar at F. (1) B Answers: (a) 0₁ = i (b) VF = i a D 2 2a W E F MPa, 0₂ = mm IN i MPa, and 03 i MPa
A 5-m long, simply supported beam is loaded as shown. Determine the lightest W-shape beam that can be used such that the flexural stress will not exceed 94 MPa. Use the table for standard properties of W-shape beams. Also, determine the actual maximum stress (in MPa) in the selected W-shape beam. As for other values: P1 = 124 kN P2 = 105 kN P3 = 183 kN %3D
The 400-kg uniform bar AB shown in Fig. 1–28a is supported by a steel rod AC and a roller at B. If it supports a live distributed loading of 3 kN/m, determine the required diameter of the rod. The failure stress for the steel is o fail = 345 MPa. Use the LRFD method, where the resistance factor for tension is o = 0.9 and the load factors for the dead and live loads are yp = 1.2 and yL = 1.6, respectively. 9.60 kN/m 3 kN/m B B m- m- 2 m 4.709 kN/m (a) (b) Fig. 1-28
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
A 3 m long simply supported beam of uniform cross section is subjected to a uniformly distributed load of w = 20 kN/m in the central 1 %3D m as shown in the figure. w = 20KN/m El = 30 x 10° Nm 1 m- 1 m- -1 m P . Q wwww If the flexural rigidity (EI) of the beam is 30 × 106 N-m2, the maximum slope (expressed in readians) of the deformed beam is
Problem (5): Two designs for a beam are to support moment is equal to M=150 kN.m and I,=0.36135(10³) mª. Determine the maximum normal stress for be considered. consider the I=0.21645(10*) mª, part A and B. 200 mm. 200 mm. 15 mm 30 mm 300 mm -30 mm 300 mm -15 mm 15 mm 30 mm (a) (b)
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
5) Curved beam under bending moment The curved member is symmetric and is subjected to a moment of M. The cross-sectional area of the member is also shown. Determine the bending stress in the member at points A and B and draw the bending stress distribution on this cross-section (A-B). compare the stress distributions on the respective cross-sections. M:1300NM , R:220mm , k:42mm, h:54mm , t:12mm t mm B. h mm k mm R mm M M
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
A rectangular beam 100 mm x 200 mm carries a uniformly distributed load of 5 kN/m over its simple span of 5 m. Calculate the shear stress 1 m from the left support at a point 30 mm from the top of beam. Select the correct response: O 0.48 MPa O 0.29 MPa 0.33 MPa 0.19 MPa
Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal cylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downward traingular load with maximum intensity qo as shown. Linear q(x) 2 M1 2 2c Segment 1 Segment 2 0.5 EI El (a) Find expression for maximum compressive stress at point 1. (b) Find expression for maximum tensile stress at point 1.
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←