given the ff details below answer the ff question.a. Calculate the total active active force on the wall in kN/m neglecting cohesion above the water table while using the effective cohesion below the water table. b. locate the resultant lateral force from the base 1)* Given the following detaits below, answer the ff. questions withcored complete schutions:FIG ALABORATORY RESULTS Of 2 saLsGLCLAY SANDInitial Volume of Sai| (Saturated )| 25 cm? 25 cmFinal Volume of Scil after ouen e cm³ 15 cm?Initial moss of Soil (satuvated 949 439of Sail after aven 30¢ 28 89W=25%Im4mFinal mass3mZmTRIAXIAL TEST LAB RESULTS (SAND) m KlaCELL PRESSURE DEVIATOR300500700POREZm219143178742-5375.5996LL-50%

Dry unit weight of sand = dry weight of sand/Initial Volume of soilDry unit weight of sand =…

given the ff details below answer the ff question. a. Calculate the total active active force on the wall in kN/m neglecting cohesion above the water table while using the effective cohesion below the water table. b. locate the resultant lateral force from the base

given the ff details below answer the ff question. a. Calculate the total active active force on the wall in kN/m neglecting cohesion above the water table while using the effective cohesion below the water table. b. locate the resultant lateral force from the base

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw Free body Diagram
Determine (a) the maximum bending stress, (b) the maximum shearing stress due to V in the simply supported beam shown in the figure and (c) the shearing stress at a point 1m from the right support and 2 cm below the top. 5 cm 40 kN/m 16 kN m A 1-+-2 2 m m CF -2 m 16 cm
2
The solid circular section EF rod in the figure is fixed to the wall at point F. Forces P1 = 1 kN, P2 = 2 kN were applied from point D of the DE rod, which is rigidly connected to the rod. Calculate the stress states occurring at points A and B and show them on the small volume elements removed from these points. The diameter of the EF rod will be taken as d = 50 mm. Do not give answer in image and hand writing
Please solve the problem in the picture
Considering the fully restrained beam shown in Figure 2 where E = 200 GPa and I = 2x10^9 mm^4 If P = 70 kN, M = 100 kNm, L = 12 m., and G = 40 degrees. Use either the virtual work method or the method of consistent deformation and state what you use with a complete solution. thank you. 1. Determine the maximum positive and negative shear that is acting on the beam. 2. Determine the maximum positive and negative moment that is acting on the beam 3. Determine the maximum deflection of the beam. 4. If the maximum deflection is limited to 10mm, determine the diameter of the circular beam required.
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
A planar truss tower structure is shown in the figure. P. Externally determinate Q. External static indeterminacy = 1 R. External static indeterminacy = 2 S. Internally determinate T. Internal static indeterminacy =1 U. Internal static indeterminacy = 2 Which one of the following options is correct? (A) P-False, Q-True; R-False; S-False; T-False; U-True (B) P-False, Q-True; R-False; S-False; T-True; U-False Consider the following statements aboout (C) P-False, Q-False; R-True; S-False; T-False; U-True the external and internal determinacies of the truss. (D)P-True, Q-True; R-False; S-True; T- False; U-True
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m -P B 3.5m7 Find the location x of the largest additional vertical force that can be applied to the bar. meters in 2 decimal places
A pipe with a weight of 3.7 kg/m is attached to a wall such that all degrees of freedom are restraint. At the free end of the pipe a vertical load P=100 N pointing downwards is introduced with an excentricity of 100mm from the axis. The pipe has an length of 1m and is made of steel with the Young's modulus of 210 GPa and the Poisson ratio of 0.3125. The moment of inertia is l=19.7 cm“ whereas the polar moment of inertia J = 2 I. First, as part of the mechanical properties determine the Shear Modulus. Then determine the total vertical deflection at the point where the vertical load is being introduced. Note: Use the principal of superposition. ANSWERS: Shear Modulus %3D [MPa] Vertical deflection due to weight only [mm] Vertical deflection due to End-Load (excentricity NOT considered) [mm] Vertical deflection due to excentricity of the End-Load only [mm] Total vertical deflection [mm]
The same torque is applied to two tubes with identical metal sheets, determine the ratio of square/ circle of the shear stresses. Given: r = 16 mm, %3D S = 17 mm, and t = 2.80 mm. %3D ト

lute flexural stress. For the beam shown in Figure (3), given INA = 1.+ 10 mm", calculate the transverse shearing stress at points A, C and G on the section at the left support of the beam.