Given that each of the three members of the frame in Figure 5 has a mass per unit length of 4 kg/m. Determine the position (x, y) of the center of mass (centroid). Neglect the size of the pins at the joints and the thickness of the members. Finally, calculate the reactions at the pin A and roller E. Present your answer in a FBD of the frame. 5 m- -5m E 7m

Given that each of the three members of the frame in Figure 5 has a mass per unit length of 4 kg/m. Determine the position (x, y) of the center of mass (centroid). Neglect the size of the pins at the joints and the thickness of the members. Finally, calculate the reactions at the pin A and roller E. Present your answer in a FBD of the frame. 5 m- -5m E 7m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position
The figure below shows a painting hanging from a nail fixed into the wall. The picture is supported by a strong, light string attached to the picture symmetrically at two points along the top of the frame. 0.1 m 420 42 05 m 0.75 m Draw a free-body diagram of the painting. If the tension in the string is 60 N, what is the weight of the painting? A person tries to move the painting to the right by pushing on the bottom left edge with a force of 10 N. What moment does this exert about the nail? What force would the person need to apply to the top left edge instead to exert the same moment?
Question One Find the centre of mass of the uniform lamina ABCDE shown below. E 6cm 30 A 10cm B The shape is symmetrical about the line through C.
The cylinders in the figure shown are piled in a rectangular ditch as shown. The radii of cylinders A,B and C are 4m , 6m, and 5m respectively. Neglecting the friction. Determine the reaction between the wall and B in kN.
1) Determine the reaction at roller A. Express your answer to three significant figures and include the appropriate units. 2) Determine the horizontal and vertical components of reaction at pin B(Bx,By) . Express your answers in newtons to three significant figures separated by a comma.
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
This airplane nose wheel assembly is raised by applying a torque M, as shown. The arm AD and the wheel have a combined weight of 100lbs, and the center of gravity is at G, as shown. Determine the torque required to maintain the assembly at the configuration shown in the following figure (D is directly below B and ?= 15°).
The mass center Gof the 1490-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. -1290 mm-976 mm- Answers: Normal force under each of the front tires: N; = i N Normal force under each of the rear tires: N, = N z z
2. The backhoe supports a 7.5 kN weight of soil in the bucket which has a center of gravity at G. Find: 0.64 m 0.25 m ● 0.26 m 0.3 m 1.68 m Force in cylinder ED (indicate if force is in tension or compression) Force in cylinder FI (indicate if force is in tension or compression) OF 0.4 m 0.1 m A -1.44 m- 17.5 kN 0.25 m D B m E 0.22 m 0.45m H O SUSIS Force in ED = Force in FI = KN (Tor C) kN (Tor C)
5/27 Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully observe the proper sign of the radical involved.)
Q1 The signboard with a mass of 100 kg (with centre of mass at point G) is to be attached to the rod AB as shown in Figure Q1. Rod AB is joined with ball-socket to point A. Point B is supported by two rods BC and BD. The location of each point is revealed as A (0,0,0), B (0,2,0), C (1,0,2) and D (-2,0,1). Solve the followings: Detemine the x, y and z components of force reaction at joint A, and (i) (ii) Calculate the tension within the rods BC and BD.
Determine the magnitude of the vertical support reaction at Point A. Enter your number to TWO decimal places, If an integer, just enter the integer number. Remember, the appropriate unit! (If applicable, use a "-" to indicate multiply in the unit.) A - 6m- 0.5 kN/m -3 m- 3 kN 5 kN•m