Given that: 1) The length of L4 of link AB is 1 m. 2) The length of L1 of link CD is 0.5 m. 3) The length of L3 is 1 m. 4) The length of L2 is 0.5 m. 5) The angular velocity of link AB, WAg is 5 rad/s, moving in the direction shown on the figure. 6) The angular acceleration of link AB, aAB is 10 rad/s?, moving in the direction shown on the figure. Hints: 1) Please enter numerical values only. Do not include any units in your answers. Determine: (a) the angular acceleration of link BC, GBc in radis?, in three significant Figures. (b) the angular acceleration of link CD, aco in rad/s?, in FOUR significant Figures

Given that: 1) The length of L4 of link AB is 1 m. 2) The length of L1 of link CD is 0.5 m. 3) The length of L3 is 1 m. 4) The length of L2 is 0.5 m. 5) The angular velocity of link AB, WAg is 5 rad/s, moving in the direction shown on the figure. 6) The angular acceleration of link AB, aAB is 10 rad/s?, moving in the direction shown on the figure. Hints: 1) Please enter numerical values only. Do not include any units in your answers. Determine: (a) the angular acceleration of link BC, GBc in radis?, in three significant Figures. (b) the angular acceleration of link CD, aco in rad/s?, in FOUR significant Figures

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q4 shows a structure that consist of link AB, link BC and link CD. The link CD hasthe angular velocity of 2 rad/s and the angular deceleration of 4 rad/s2. 1. Draw the kinematic diagram of acceleration for link BC. 2. Determine the angular acceleration of link BC 3. Determine the angular acceleration of link AB
This problem must be solved using the method of Instantaneous Center of Zero Velocity (IC method). 1) Find Va, VB, and wz when Link 2 = 2, Link 3 = 6, offset = -3, 02 = 60°, w2 = 8rad/sec 2) Find VA, VB, and wz when Link 2 = 3.5, Link 3 = 10, offset = 1, 02 120°, w2 = 8rad/sec 03 B Y Link 3 A Offset Link 2 02 04 = 90° %3D X 02 Slider position d
A wheel executes 197 radians to coast to rest from a speed of 76 rad/s. Assuming constant deceleration, find the time required for the wheel to come to rest. Answer: Tavior Tea
The plot below shows the acceleration of a mass placed at the end of a beam as it oscillates: 20 Which we model as: Acceleration (m/s²) 15 10 5 0 -5 -10 -15 -20 0.5 1 Wd 1 1.5 1 2 = wn√1 y(t) = Ae-3wnt sin(wat) y(t) = Ae-Ct sin 1 2.5 Time (s) = 2π T 2π T 1+ 3 2π We will use MATLAB to find the decay constant C and the period T. We can then use these to calculate the damping ratio and the natural frequency @n, using: 3.5 T 4 2 and C = {wn O data zeros peaks decay fit 4.5 Using the information above, derive the expression shown below for the damping ratio 3. 1 3 = 5
Needs Complete typed solution with 100 % accuracy.
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 4) if W = 4.0 rad/s and a = 6.3 rad/s2, length I = 1.5 m, and angle 0= 36°, what is the magnitude of the angular velocity of link AB? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m 0, a B Your Answer: Answer units
In the figure, link 2 rotates with constant annular velocity CO2. A slider link 3 moves outwards with a constant relative velocity where Q is a Point on slider 3 and P is a point on link 2. The magnitude and direction of Coriolis component of acceleration is given by Q on 3 VOP 002 -P on 2
The inversion of the slider-crank mechanism shown in the figure is driven by link 2 at an angular speed and acceleration of 60 rad/s ccw and 240 rad/s2 cw, respectively. Find the velocity and acceleration of point B.|AO2|=75 mm, |BA|=400 mm, |O4O2|= 125 mm. (Using Complex Algebraic approach do the Position Analysis; Velocity Analysis and Acceleration Analysis then solve the problem please)
The in-plane angular speed of the bent bar indicated below is w = 0.2 rad/s. The dimensions of the bar are L = 0.4 m and H = 0.6 m. Find the magnitude of the velocity (in m/s) of the endpoint B. H B L Figure is from "Engineering Mechanic An Introduction to Dynamics", McGill and King.
5.) A man is about to throw a stone by rotating his fully extended arm. If the stone moves at v = 2 due to the motion of his arm, what is the magnitude and vector equation of acceleration in for the stone if the man's arm is 550 mm long?
In a certain slides-crank mechanism, lengths of crank aid commenting rod are equal. If the crank rotates with a uniform angular speed of 14 rad/s and the crank length is 300 mm, the maximum acceleration of the slider (in m/s²) is
M1