7. The one-line loaded diagram of unloaded power system is shown below. Reactance of thetwo sections of transmission line is shown on the diagram. The generators andtransformers are rated as follows:Generator 1: 20MVA, 13.8kv, x"- 0,2 per unitGenerator 2: 30OMVA, 18kv, x"= 0.2 per unitGenerator 3: 30OMVA, 20kv, x"= 0.2 per unitTransformer T1: 25MVA, 220 Y/13.8kv A, x-10%Transformer T2: single phase units each rated 10MVA, 127/18, x-10%Transformer T1: 35MVA, 220 Y/22kv Y, x-10%Draw the impedance diagram with all reactance marked per unit and with letters toindicate points corresponding to the one-line diagram. Choose a base of 50MVA, 13.8kvin the circuit of generator 1.j80 0j100 Q"కాతంణం

Given, Base MVA=50 MVA Base KV=13.8 KV Expression to calculate the reactance on new base MVA &…

Generator 1: 20MVA, 13.8kv, x"- 0,2 per unit Generator 2: 30OMVA, 18kv, x"= 0.2 per unit Generator 3: 30OMVA, 20kv, x"= 0.2 per unit Transformer TI: 25MVA, 220 Y/13.8kv A, x-10% Transformer T2: single phase units each rated 10MVA, 127/18, x-10% Transformer T1: 35MVA, 220 Y/22kv Y, x-10% Draw the impedance diagram with all reactance marked per unit and with letters to indicate points corresponding to the one-line diagram. Choose a base of 50MVA, 13.8kv in the circuit of generator 1.

Generator 1: 20MVA, 13.8kv, x"- 0,2 per unit Generator 2: 30OMVA, 18kv, x"= 0.2 per unit Generator 3: 30OMVA, 20kv, x"= 0.2 per unit Transformer TI: 25MVA, 220 Y/13.8kv A, x-10% Transformer T2: single phase units each rated 10MVA, 127/18, x-10% Transformer T1: 35MVA, 220 Y/22kv Y, x-10% Draw the impedance diagram with all reactance marked per unit and with letters to indicate points corresponding to the one-line diagram. Choose a base of 50MVA, 13.8kv in the circuit of generator 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. (ii) A 12 kVA, 56HZ, single-phase transformer has a turns ratio of 18 : 2 and is supplied from a 2.5 kV supply. Neglecting losses, determine (a) the secondary voltage, (b) the full load primary current, (c) the maximum flux and (d) the minimum value of load resistance which can be connected across the secondary winding without the kVA rating being exceeded secondary voltage primary current maximum flux secondary resistance
A 4-bus three-phase power system consists of the following equipment: • Generator 1 connected to bus 1 with a rated power of 20MVA, rated voltage of 20 kV, and a series reactance of 0.4 p.u. • Generator 2 connected to bus 5, with a rated power of 12MVA, rated voltage of 10 kV, and a series reactance of 0.3 p.u. Transformer 1 connected between buses 1 and 2, is wye-wye connected with a rated power of 20 MVA, rated voltages 20/100 kV, and a series reactance of 0.1 p.u. • Transformer 2 connected between buses 4 and 5, is wye-wye connected with a rated power of 12 MVA, rated voltages 12/110 kV, and a series reactance of 0.15 p.u. • Transmission Line 2-3 connects buses 2 and 3 and had a series impedance of 50 + j75 ohms. • Transmission Line 3-4 connects buses 3 and 4 and had a series impedance of 40 + j80 ohms. • Load A connected to bus 3 and abosorbes20 MW and 10 MVAR. The voltage at bus 3 is 105 kV. 1) Draw the one-line diagram for the system. 2) Draw the per-unit, per phase…
A 220-kVA transformer with .2% resistance and 4% reactance and another 120-kVA transformer with 3% reactance and .15% resistance with the same voltage ratio. the phase angle is 33 degree and the total load .25 MVA. How much the load of each transformer. what are the load currents of each transformer if a1 =20 and a2=25?
Please answer all subparts than i will like a. A current transformer (CT) is rated 200/5 and has a secondary current of 4.0 A. Determine the primary current. b. A 150/5 CT has the primary conductor looped to pass through the donut three times. If the secondary current is 3.0 A, determine the primary current. c. A 60/5 CT has the primary looped to pass through the donut two times. With 25 A in the primary, determine the secondary current. d. A voltage (potential) transformer is rated for 14.4 kV / 115 V and is used to measure the voltage on an industrial power line. If the voltmeter indicates 111 V, calculate the voltage in the power line.
3) A three-phase transformer of 60 kVA (three-phase power), 13200/480 V (line A line) in delta-strella connection has a resistance of 0.02 PU and a reactance of 0.08 PU. For this transformer, calculate: a) The voltage regulation at full load and F.P. 0.85 in delay. (b) The regulation of voltage voltage to full cargo and F.P. Unitarian. c) The voltage regulation at full load and F.P. 0.85 in advance.
The Y/Y connected 3-phase step-up transformer has a rating of 1200 MVA, operating at 33 kV/340 kV and 60 Hz. Its impedance is characterized solely by a reactance of 11.5 percent. Its purpose is to increase the voltage from a generating station in order to supply power to a 340 kV transmission line. Answer the following questions: a) Draw and determine the equivalent circuit of this transformer, per phase, in per-unit. b) Using the per-unit method, determine the generator terminal voltage when the high-voltage (HV) side of the transformer supplies 800 MVA at a power factor of 0.90 with a lagging angle, and the voltage is 360 kV. Hint: Select the nominal voltage as a base voltage, and the nominal power rating as a base power.
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.
The nameplate on a 25-MVA, 60-Hz single-phase transformer indicates that it has a voltage rating of 8.0-kV:78-kV. A short-circuit test from the high-voltage side (low-voltage winding shortcircuited) gives readings of 4.53 kV, 321 A, and 77.5 kW. An open-circuit test is conducted fromthe low-voltage side and the corresponding instrument readings are 8.0 kV, 39.6 A, and 86.2 kW. (a) Calculate the equivalent series impedance of the transformer as referred to the high-voltageterminals.(b) Calculate the equivalent series impedance of the transformer as referred to the low-voltageterminals.(c) Making appropriate approximations, draw a T equivalent circuit for the transformer.(d) Determine the efficiency of the transformer if it is supplying rated load (unity power factor)at rated voltage at its low-voltage terminal
The actual equivalent circuit parameters of a single-phase transformer operating at 220/110 volts are given as follows. R1=0.2 ohm, X1=0.3ohm, RFe=45 kohm, Xm=5 kohm, R2=0.025ohm, X2=0.075 ohm Using the L-equivalent circuit, a) reduce the secondary circuit parameters to the primary b) Since a reduced load of 44.72+j32 ohms is connected on the secondary side, calculate the primary current, the load current, and the total copper losses.