From the given figure ; compute the cross-section area (sq.ft) and hydraulic radius (ft) at section 1:

Q: The dimensions of this duct are in feet.a. Find in centimeters the width of the duct

A:

Q: Determine the hydrostatic force acting on the horizontal bottom and on the vertical ends of the…

A: Given : Depth of water = 5' Width = 8' Length = 10'

Q: A wide channel has water flowing with a depth of 0.5m and the velocity on the surface is 2 m/s. At…

A:

Q: 20 ft -200 ft- Exercise Figure 8.1 8.1). The concrete has a unit weight of 2.4 Mg/m³ (150 lb/ft3).…

A:

Q: For the two-dimensional flow system shown below (units in meters): Express how you will calculate…

A: Flow net is the graphical representation of flow lines and equipotential lines. Flow lines depict…

Q: Describe how the hydraulic grade line is determined for: a. open channel flow and b. at the outlet…

A: Hydraulic grade line represents the sum of pressure head and datum head. So value of HGL changes…

Q: solve it please

A: Step 1: Step 2:There is Lil change in numbers like there is 26 instead of 20 and so on  Hope you got…

Q: Q-1: Water is flowing through a soil as shown in the figure. Determine the elevation, pressure, and…

A:

Q: Sum of the length of the solid boundaries of the section in contact with the fluid is known as A.…

A: Given: Sum of length of the solid boundaries of the section in contact with the fluid is known as…

Q: Water is flowing through the formation shown at a constant Darcy velocity. The following information…

A: Given- Hydraulic head at the top =18 feet Hydraulic head at the bottom = 28 feet K1 = 2 ft/day K2 =…

Q: A 5 KN 5 KN 5 KN 5 KN 5 KN 1m 1m 1m 1m 1m 20 kN-m DRAW V&M DIAGRAM. SOLVE FOR V-MAX NEGATIVE, V-MAX…

A: Solution:*MB = M5

Q: Q1/ For the hydraulic structures below, Q = 20o0m3/sec, water way = 100m, Pond level = 160m, safe…

A:

Q: Refer to the figure shown, if h1=150mm, h2=300mm, b=300mm, fc'=35MPa and fy=420MPa. Determine the…

A: From the given figure it is required to find the depth of balanced compression block.

Q: Problem Number 2: In the Given Rectangular Dam, determine the magnitud intersects the base AB.

A:

Q: The hydraulic radius is defined as half of the hydraulic diameter of a section. True False

A: The hydraulic radius is defined as half of the hydraulic diameter of a section. This statement is…

Q: A two-dimensional square channel redirects a water flow from horizontal uniform to vertical…

A: h= 75.5 mm P= 185 kPa M= 2.05 kg V= 0.00355 m3 Vmax= 2Vmin To find-  a) Vmin when U= 7.5 m/s b)…

Q: Determine the point where the neutral axis intersects line AB. The point where the neutral axis…

A: Given,  Wall thickness= 12mm P= 19kN

Q: Problem #1 (Pipes Iterative Analysis): Water at 70°F flows through 100 feet of pipe 10 inches in…

A:

Q: Problem Water is pumped through a vertical steel pipe to an elevated tank. D = 10 cm, P₁= 1.6 MPa, L…

A: Given data:- Diameter of pipe, D=10 cm Length of the pipe, L=80 m Pressure, P1=1.6 MPa=1.6×106 N/m2…

Q: Problem: Determine þPn for the short column shown. fy = 60000 psi and f'c = 4000 psi. 3" & = 8" 8…

A: A short column is the one whose ratio of effective length to its least lateral dimension is less…

Q: Problem #1 Determine the magnitude and the location of the hydrostatic force on the 2 m by 4 m…

A:

Q: gate

A:

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

A: From the given question it is required to calculate the surface water elevation in reservoir A.

Q: 7. The formula for hydraulic diameter is

A: Hydraulic diameter deals with the flow of non-circular channels. There are three types of hydraulic…

Q: Determine the elevation, pressure, and total hydraulic heads at all points, a through g using Datum…

A: step 1-

Q: Water flowing along a horizontal pipe has a speed of 2.77 m/s and a pressure of 4.41 atm. Further…

A: Solution:- By assuming flow is laminar such that the Bernoulli equation can applied. Given initial…

Q: For the concrete dam shown, where b=0.80m, H= 8m and h3D7m. Unit weight of concrete is 24kN/m3.…

A:

Q: = Problem: Determine Pn for the short column shown. fy 4000 psi. ●8 # 10. 3-4-5--3-- 8" 3" 14" 20"…

A: fy = 60000 psif'c = 4000 psiTo Find : ?

Q: The dimensions of this duct are in feet.b. Find in centimeters the height of the duct.

A: Given data- Height of the duct given (H) = 2 ft.

Q: Water resources engineering Please refer to the attached image. The new cat iron pipe carrying a…

A: Given data: Flow in pipe is 0.3 ft3/s. Elevation at reservoir surface is 1300 ft. Elevation at point…

Q: The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Determine…

A: Determine the horizontal component of the hydrostatic force against the quarter circle wall

Q: A fluid with a kinematic viscosity equal to 2,951E-5 ft2/s moves within the section Shown. It is…

A: Given, Re = 27066 v = 2.915 x 10-5 ft2/s

Q: Calculate for the hydraulic gradient if the pressure at point A is 18547N and 15874N for point B.…

A:

Q: resultant force R exerted on the gate by the water pressure i

A:

Q: There s a leak in a horizontal 30cm pipeline (f=0.025). Upstream from the leak two gages 600m apart…

A:

Q: Question-1 Hydraulic Engineering (Open Channel Hydraulics) Water is flowing in the trapezoidal…

A:

Q: Why does the hydraulic radius and shape factor have been developed?

A: Hydraulic Radius: The Hydraulic radius is the ratio of the pore volume to the pore surface area of…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.