Quèstion 34 pFrom the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is its modulus of elasticity?600MPa600r 10 psi506040040040201000.050.100.15StainO A. 320 GPaO B. 500 GPaOC.400 GPaO D.215 GPaSem (MP

Answered: Image /qna-images/answer/3171f21a-019a-47b1-8ca7-7d5a59c5dd3f.jpg

Answered: From the following figure shows the…

From the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is its modulus of elasticity?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
Question 5: Based on the stress-strain diagram for a material shown here, find the followings: Yield strength (MPa = Ultimate strength (MPa) = %3D Ductility (%) = Rupture strength (MPa) =
During the test of hardness due to Brinell, the diameter of the testing sphere was0.01m, the exerted load was 3.0 tons and the diameter of the indented area wasapproximately 0.003 m. Find the value of the hardness for this material. Also find theTensile strength if the proportionality constant was approximately 3.45.
An ordinary mild steel bar has been prestressed to a working stress of 200 MPa. If the Young's modulus of steel is 200 GPa and permanent negative strain due to shrinkage and creep is 0.0008, what is the effective stress left in the steel?
Ductile materials have more impact strength compared to brittle materials. Select one: True False
A material with an Ultimate Tensile Strength (UTS) of 400 Mpa is loaded cyclically about mean stress of 80 MPa. If the stress range that will cause fatigue fracture in 100 000 cycles under zero mean stress is (+,- )60 MPa, what stress range (in MPa) about the mean of 70 MPa will give the same life
Case Study Calculate the Tensile Toughness Tensile toughness measures the total energy absorbed prior to fracture and is different from fracture toughness and impact toughness. Fracture toughness measures the resistance to fracture when a flaw (i.e. crack) is present in the material. Since it is nearly impossible and costly to manufacture materials with zero or near zero defects, fracture toughness is a major consideration for all structural materials. Impact toughness measures a materials ability to withstand an impact blow (i.e. high strain rates) and is particularly important in assessing the ductile-to-brittle transition behavior (more details later). Impact toughness is also commonly referred to as notch toughness. The tensile toughness can be estimated using the stress-strain curve by measuring the area under the curve (both the elastic and plastic regions). Tensile Toughness = f Stress, σ Ty- Ey Efracture ETS Ur Ey Efracture o de = U₁ + SETS o de + Sefracture o de Ey Ey o de =…
An annealed-steel specimen has a 0.750 in. diameter and a 12.000 in. gage length. Maximum load is reached at 60,000 lbs and fracture occurs at 30,000 Ibs. For this steel, E= 360 x 10° psi. (a) Draw a sketch of stress-strain diagram for a typical steel in tension? (b) What is the ultimate tensile strength (UTS)? (c) Why does fracture occur at a lower load than the maximum load? (d) What is the elongation when a tensile stress of 30,000 psi is applied? A 400-mm-long rod with a diameter of 4.5 mm is loaded with a 5000-N weight. If the diameter decreases to 3.5 mm, compute the final length of the rod. 3. 4. A steel rod 1.5 m long and 75 mm x 75 mm in cross-section is subjected to a tensile force of 160 kN. Determine the elongation of the rod, if modulus of elasticity for the rod material is 900 GPa. 5. A hollow cylinder 4.5 m long has an outside diameter of 80 mm and inside diameter of 60 mm. If the cylinder is carrying a load of 75 kN, find the stress in the cylinder. Also find the…
Which one is the correct answer please? Thank you
Please do it typed not handwriting. Make sure the answer is correct Don't copy from any other online answers please
2. The diameter of a bar fabricated from an alloy with properties shown in figure below reduced from an initial 1.2 in. to a 1.0 in. diameter, to a final 0.8 in. diameter. For parts a, b, and c; when using the graph, you can ignore the marked points A, B, C, and O (a) Determine the % CW after the first step of the process (b) Determine the yield stress (in ksl) after the first step. of the process (c) Determine the % CW after the second step of the process 22 Tensile strength (ksi) 20 18 Yield strength (ksi) 16 14 12 10 Elongation (%) 4 2 20 40 60 80 Property
What is the "flexure formula?" along with what are the units for the flexture formula as well as the equation.