From the following data:Prepare the table of mass ordinate.Use end area method to calculate the volume.Shrinkage factor 20 %StaEnd Area (sq m)MassCutFillOrdinate1+000601+020401+04020101+06010401+080501+10080

End area formula for calculation of volume is given by volume=A1+A22×L; where A1 is area at station…

Answered: From the following data: Prepare the…

From the following data: Prepare the table of mass ordinate. Use end area method to calculate the volume. Shrinkage factor 20 %

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter3: Measuring Quantities Generally

Section: Chapter Questions

Problem 13RQ

See similar textbooks

Related questions

Q: 2. Another reinforced concrete beam has the following properties: • fy= 60 ksi • f= 5,000 psi • As =…

Q: 1. Complete the given table Sieve number Diameter(mm) Mass retained Cumulative Mass Percent Passing…

Q: 7. What is the vertical reaction at the hinge support? (kN) 8. What is the horizontal reaction at…

A: The supports of the given beam is of two types, Roller support Hinge support The roller support…

Q: Q. No. 1 Compute the discharge in the open channel shown in fig 1 below having bed slope of 1 in…

A: Given data Bed slope Mannings roughness coefficient Value of R To find Discharge

Q: Refer to the figure shown below,i if F = 855 N 144 90 C. O 72 O 120 200 mm A Which of the ff. most…

A: Given F = 855 N Required Moment of force F about x and y axis

Q: 100 90 80 70 60 50 40 30 20 10 0.5 0.05 Grain size (mm)-log scale From the graph D60 = 0.997 mm; D30…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm.

A: Volume of 1=(40×17×38) - Volume of 2 =(40×17×38) - 12×10×10×17…

Q: B) Determine the reaction forces of a rigid plate. To check the solution you will need to specify…

Q: A truncated right prism has an equilateral triangular base with one side measures 3 cm. The lateral…

Q: Derive the relationship that exists among the ff: Porosity, bulk density and particle density…

Q: The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the…

Q: 2.4 25 kN/m 15 kN/m E Hinge A 11 -10 m Hinge Ray = 170.25 KN Rax = 309.25 KON Ma = 11128-50 KN-M 15…

A: Free body diagram: The angles; θ=tan-1103=73.3 Conver the UDL to point load: Slant…

Q: Instructions: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with…

A: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with each…

Q: For the section where 0 < x < 5.0 ft, find the shear force V(x) and the bending moment M(x) as a…

A: Since, R=1000lb Moment about A is zero By * 10- (1/2) * 5 * 400* (2/3)*5 =0 By=333.33lb…

Q: Part A Determine the mass moment of inertia of the thin plate about an axis perpendicular to the…

Q: 12. Given the following data for a stream of uniform flow: 15pts A = 6.97 sq.m. P = 9.76 m S=0.007…

Q: PROBLEM 7: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have…

Q: Shear stre Choose the correct answer ss has units: a. Nt m e. Viscosity v times area…

A: given data : the units of shear stresss a. Nt m b. Nt m2 c. Nt/m2 d. Nt/m e.…

Q: Determine the volume of voids, volume of solids, density, rate of absorption, moisture content and…

Q: A surveyor set his instrument up at point A to observe points B and C which are both ahead of his…

A: Given data- The given situation is shown below- Where, i= 2.703 mmd=10 cm = 100 mmf = 27 cm = 270…

Q: ly- f= 6,000 psi • As = 7.07 in? • b = 16 in • d= 30 in a) Compute the depth of the compressive…

Q: 1. Locate the center of mass of the figure shown below. Where the vertical face has of 30 kg/m^2,…

A: This problem is related to solid mechanics. In this problem given about mass and dimensions of…

Q: Determine the maximum safe capacity of an axially loaded hinged ends column having an unsupported…

A: This is already answered question.In this question ask about that how we get the Circle value.(ie…

Q: 3 praw A m the influence E 't 2 FOT B + line of moment at point D 1. S + 0.5 C

A: Solution: Influence line for bending moment at D: Introduce a hinge at D and a unit bending moment…

Q: A certain unsharpened cylindrical pencil is 0.25 inches in diameter and 10 inches long. what is the…

A: Given: Diameter of the unsharpened cylindrical pencil, D = 0.25 in Length of the unsharpened…

Q: Convert the strength of selected materials given in the accompanying table from MPa to ksi, where…

Q: Design a W14, 20ft long column to carry an axial load of 800k. Fy=50ksi, fix - pin condition and…

A: Length of column about X axis(Strong direction) Lx = 20 ftLength of column about Y axis(Weak…

Q: Complete the table if the oven dried mass is 161.42 grams. Make sure you show your solutions and…

Q: A B 30 7. Determine the maximum force P that can be applied without moving the two Y-kg crates.…

Q: Given the following data: A. Loose Unit Weight Determination Fine Aggregate a. Weight of measure, g.…

Q: Locate the center of mass of the homogeneous block assembly. 250 mm 200 mm 150 mm 100 mm 150 mm 150…

A: Centre of mass: Centre of mass is defined as a point relative to system of objects . In other words…

Q: Given data : Work done=20 Joule Displacement=5 m Calcualte force applied

A: This question is related with mechanics . In this question we are provided with value of work done…

Q: Convert the strength of selected Materials given in the accompanying table from MPa to ksi, where…

Q: A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s volume is…

A: Given data, Pressure P2 = 4666 psi Volume V1 = 805.407 in3 Bulk modulus K = 305000 psi

Q: below. A smaller square chunk was cut from the square block, leaving a hole in the figure. Find the…

Q: Using Nominal Mix Design, calculate the individual quantity of cement, sand, gravel, and water for…

Q: Analyze the given frame. 53kN/m 3m pin 53 37.1kN/m 5m kN/m Am 4m

Q: Consider a simply supported steel beam with maximum moment occurring at midspan. Let the beam be…

A: A simply supported beam having maximum moment occurring at the mid span. The yielding stress is Fy…

Q: Using Nominal Mix Design, calculate the individual quantity of cement, sand, gravel, and water for…

A: The given values are as follows,F=1.54ρcement=1440kg/m3ρsand=1600kg/m3ρgravel=1560kg/m3The water of…

Concept explainers

Total Energy Consumption

The term energy consumption signifies the consumption of electricity. Energy consumption as electricity is a primary demand for households, factories, industries, complexes, and commercial places. According to a report, the total U.S. energy consumption for 2018 was 101 BTU (British Thermal Units). It accounted for 17% of the total energy consumption of the world. The total energy demand for the U.S. as oil equivalent was estimated to be about 6804 kg of oil equivalent.

Question

From the following data:
Prepare the table of mass ordinate.
Use end area method to calculate the volume.
Shrinkage factor 20 %
Sta
End Area (sq m)
Mass
Cut
Fill
Ordinate
1+000
60
1+020
40
1+040
20
10
1+060
10
40
1+080
50
1+100
80

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q/Deduce the ISO from the projections 60 8 30 40 R30
A truncated right prism has an equilateral triangular base with one side measures 3 cm. The lateral edges have lengths 5 cm, 6 cm and 7 cm. Find the total surface area. Express your answer in 1 decimal place.
PROBLEM 7: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have densities of 2700 kg/m3, 5700 kg/m3, 7800 kg/m3respectively. Note: DRAW OR ILLUSTRATE THE SUB-VOLUMES AND INDICATE THE CENTROID OF EACH SUB-VOLUME BEFORE ANY NUMERICAL SOLUTIONS.
The net area in tension, Ant, of the L6 x 6x 3/8 angle shown in the figure is equal to:
Determine the shape factor
Photographs at a scale of S are required to cover an area X-mi square. The camera has a focal length f and focal plane dimensions of 9 x 9 in. If endlap is 60% and sidelap 30%, how many photos will be required to cover the area for the data given below? Part A S=1:6200; X= 8; f = 152.4 mm Express your answer as an integer. 195| ΑΣΦ ↓↑ Number of photos = 360 vec Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining ?
Answer should be in 4 decimal places. Ill upvote, Thanks
Determine the force (P) required to cause impending motion, given that µs = 0.43 and uk = 0.25. F1 = 506 and 0 = 25 %3D **Type your answer in two (2) decimal places without the unit. F.
Show complete and detailed solution. Draw illustrations
Compute the coordinates of the centroid (x, y) of the area shown. The a b лу a жоже Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 45 mm 27 mm с 23 mm d 90 mm The x coordinate of the centroid is = Y 2013 Michael Swanbom cc) +❀O BY NC SA coordinate of the centroid is d C x mm. mm.
E Apps Apple Disney ESPN Yahoo! O Bing 6 Google 6 Yahoo A Imported From Sa...
Compute the coordinates of the centroid (7,5) of the area shown. y a b 3 с d h พ kd b 13 mm 88 mm 15 mm 51 mm 93 mm 25 mm The a coordinate of the centroid is The y coordinate of the centroid is y 2013 Michael Swanbom cc 30 BY NC SA Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value mm. ↑ a mm. h *u* x