A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s volume is then 805.407 in3. If the water is released from the tank, how many pounds will be collected at atmospheric pressure? Use 305 000 psi as an average value of bulk modulus of elasticity

A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s volume is then 805.407 in3. If the water is released from the tank, how many pounds will be collected at atmospheric pressure? Use 305 000 psi as an average value of bulk modulus of elasticity

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a. Compute the bulk modulus of elasticity. b. Compute the percentage of volume decreas c. Compute…

Q: QUESTION 7 A cube of brass* has sides of 0.10m. Determine th isplace the top of the block 1.2x10 m…

Q: 9. A 200 kgf load is applied to a steel bar of cross section area 6 cm². When the same load is…

A: Given data: P=200 kgf=200×9.81=1962 NAs=6 cm2=6×102 mm2εs=εAlEs=2.1×105 MN/m2=2.1×105…

Q: A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: Bar Sample No. deformed deformed Туре Nominal Diameter, mm 1 25 12 12 12 Average Diameter, mm…

A: Given data, Elongation of 2nd bar = 33.25 cm Change in length of 2nd bar = 3.25 cm Change in length…

Q: 3. Convert the following: a) 650 Pa to Mpa b) 650 Pa to Kpa c) 375 kg to N

A: Given quantity; 650Pa to Mpa&Kpa 375kg to N 1MPa = 10⁶Pa Also 1Kpa = 10³Pa And, 1kg = 9.81N…

Q: ductility of a tested material in terms of percent elongation and percent reduction of area. The…

Q: A rod of length 100mm and diameter 10mm is made from an alloy. The rod was pulled with a force of…

A: Given: Original length of rod, l = 100 mm Initial diameter of rod, d = 10 mm Tensile load, P = 5.85…

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 1 MN/m² and a volume of 995 cm³ at 2…

A: A liquid compressed in a cylinder has volume, V1= 1000 cc At, P1= 1 MN/m2 V2 = 995 cc At, P2= 2…

Q: The state of stress in a long dam is as shown in the figure, Determine oz in MPa? [E = 200 Gpa, u =…

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³ at 3.3…

A: Volume of the liquid=1000 cm3Pressure = 2 MN/m2Compressed volume=993 cm3Pressure at compressed…

Q: Strain Energy Question 10 What will be the strain energy stored in the metallic bar of cross…

A: Given data- Cross-sectional area A=2 cm2, Gauge length L=10 cm, Extension =0.002 cm, Load P=12 kN,…

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: Find the change in volume of 5 ft3 of water at 80 0F when subjected to a pressure increase of 368…

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³ at 3.3…

A: Volume of the liquid V=1000 cm3 at 2MN/m2 Volume of the liquid V=993 cm3 at 3.3 MN/m2 It is…

Q: For the beam in the figure, there is a distributed load with the following equation f (x) =…

A: Solution Draw the diagram

Q: H.S An open cylinder can has an inside radius of 2 cm and an inside height of 5 cm use the total…

Q: A liquid compressed in a cylinder has a volume of 1000 cm3 at 0.95 MN/m2 and a volume of 1000 cm3 at…

Q: PROBLEM 3. Compute the capillary effect of immersion in water of a glass tube of 4mm internal…

A: The values given in the question are as follows Diameter of tube(d)=4 mm or 4*10-3 m Surface…

Q: Prob3.2. Calculate the strain energy in a bar 3 m long and 40 mm in diameter when it is subjected to…

A: Length of the bar= 3mDiameter =40mmTensile load= 100kNE= 2.05×10⁵ N/mm²

Q: A cube of dimension L and sp. gr. 0.82 floats horizontally in water. Is the cube stable? Why? Show…

A: We have a cube of dimensions L×L×L and SG = 0.82 we have to check is this body stable or not when it…

Q: The state of stress in a long dam is as shown in the figure, Determine oz in MPa? [E = 200 Gpa, u =…

Q: A piece of metal weighs 491 kN in air. When submerged in water, it weighs 67 kN. Find the volume of…

Q: B. A volume of one cum of water is subjected to a pressure increase of 14MP.. 1. Compute the change…

A: 1) negative sign represent the decrease in volume

Q: cure 1 of 1 D 60° 4m If load C has a mass of 380kg, determine the required minimum diameter of the…

Q: 3. What is the diameter change of a 50-ft spherical tank made of ½" steel plate due to internal…

A: Internal diameter = 50 ft. wall thickness = t = 0.5'' v = 0.3. p = 100 psi. E = 30,000,000 Psi.

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: Ultimate stress is the safest stress taken within elastic limit. It is the ratio of ultimate stress…

Q: 1. A steel rod is suspended vertically from one end and has a length of 100 m. If the diameter of…

Q: The state of stress in a long dam is as shown in the figure, Determine oz in MPa? [E = 200 Gpa, u =…

Q: The rectangular metal block shown in Figure is subjected to tension within the elastic range. The…

A: Given data Increase in length = 0.05 Poisson’s ratio =0.33 a =50 mm b = 25 mm The lateral strain is…

Q: A weight, with an unknown mass, falls through a distance of 10 millimeters (mm) onto a collar…

A: A weight falls through 10 mm on a collar attached to the lower end of a vertical bar.The bar is 3…

Q: A spherical ball of volume 20 m³ is placed under a certain liquid wherein the ball is subjected to a…

Q: 1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in Figure Q1 (a), can…

Q: Eight kilometers below the surface of the ocean the pressure is 81.4 MPa. Determine the density of…

A: Given- Depth h=8 km=8000 m Pressure P=81.4 MPa, B=2.87 GPa It is needed to find the density of sea…

Q: The assembly has the diameters and material indicated. Determine the displacement at D if, F1= 700…

Question

A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s
volume is then 805.407 in3. If the water is released from the tank, how many pounds
will be collected at atmospheric pressure? Use 305 000 psi as an average value of bulk
modulus of elasticity

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A plastic cube with a 100 mm X 100 mm X 100 mm. is placed in a pressurechamber and subjected to a pressure of 100 MPa. If the modulus of elasticityis 7 GPa and Poisson’s ratio is 0.39, what will be the decrease in each side ofthe block, assuming that the material remains within the linear elastic region?What will be the decrease in the volume of the cube?
A cube of side 50 mm is subjected to a pressure of 80 MPa in a pressure chamber. Determine the change in the length of cube if it has a modulus of elasticity of 200 GPa and Poisson's ratio of 0.3.
A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³ at 3.3 MN/m². What is the bulk modulus of elasticity?
Solution.
I need the answer to the question in engineering resistance
Is the block in this figure stable floating in the position shown? Show calculations.
10) Will upvote anyone who will answer
Geotechnical engineering
At a depth of 14 km in the ocean, the pressure is 71.9 MPa. Assume a specific weight at the surface of 10.1 kN/m3 and an average bulk modulus of elasticity of 2.81 GPa for that pressure range. Compute the change in specific volume in mm3/kg between the surface and 14 km depth. Round your answer to 2 decimal places.
Refer to the beam loaded as shown. What is the value of Ay?