Answered: Four resistances are connected in… | bartleby

Related questions

Question

Four resistances are connected in
series with each other to a dc source.
What will be the ratio of the voltages
across the resistance V₁ V₂ V3 if their
1
conductances are given in the ratio of
G₁: G₂: G3 :: 3:5:6?
A 10:6:5
B 30:12:15
C 6:10:5
D 12:30:15

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Suppose we have a circuit with two capacitors with C1 = 5.2µF and C2 = 11.5µF that are connected in series withan external voltage of 6.2V. What are the voltage drops across each of the capacitors?
I am having difficulty understanding the dependencies of the voltages and the current in this circuit. Here, the voltage of the battery is 6.0 V, R=5.0*10^6 Ω and C=2.0µF. a) After closing the switch for 10 seconds, how would I determine the voltages across the resitor VR and the Capacitior VC? b) How would I sketch the dependance of the voltages VR and VC in relation to time? c) How would I determine the current in the resistor after the switch is closed for 10 seconds?
!! The circuit in the figure below has been connected for a long time. Let R, = 12 Q, R, = 9 N, and V = 16volts. 1.00 N R1 1.00 µF R2 2.00 N RC1 (a) Find the Charye on the capacitor. Q = HC (b) If the battery is disconnected from the circuit, what is the time constant when the capacitor discharges? T3D sr (c) Over what time interval does the capacitor discharge to 0.35 of its initial charge? Time =
A capacitor is discharged in an RC circuit. The current decreases to 50% of its initial value in 1.8 seconds.What is the time constant of the circuit? A) 0.39 sB) 1.7 sC) 3.6 sD) 1.8 sE) 2.6 s
18 µF 30 μF 3 μF 13.2 μF O 2 μF 4 µF HH 3.0 μF 30 V
5. An electric circuit contains a resistance R and a capacitor C in series, and a battery supplying a time-varying electromotive force (or voltage) V(t). The charge q on the capacitor therefore obeys the following differential equation: Rdq + 2 = V(t). dt Assuming that initially there is no charge on the capacitor, and given that V(t) Vosinut, where V₂ and w are some constants, find the charge on the capacitor as a function of time. = Hint: You may have to do integration by parts twice to evaluate the following inte- gral: feRc sin(wt)dt.
The figure shows a simple RC circuit consisting of a 100.0-V battery in series with a 10.0-µF capacitor and a resistor. Initially, the switch S is open and the capacitor is uncharged. Two seconds after the switch is closed, the voltage across the resistor is 37 V. R S www 100.0 V T 3 0.0.37 Ω O 2.0 × 105Q Ο 2.70 Ω O 4.3 × 105Q O 5.0 × 104Q 10.0 uF Determine the numerical value of the resistance R.
A 4.0-2 resistor is connected to a 12-02 resistor and this combination is connected to an ideal dc power supply with voltage V = 12 volts as shown in the figure. What is the value of current in the 12- resistor? O 1 A O 3 A 12 A O 15 A O 4 A 4.00 www www 1202
If a constant current of 1.0 mA were to flow into a 200 µF (microfarad) capacitor, what would be the voltage across the capacitor after 3 seconds?
A series circuit has two resistors with values R1 = 7.0 Ω and R2 = 2.0 Ω. If the potential of the circuit is 10.0 V, what is the current through R1?
The values of the components in a simple series RC circuit containing a switch and an initially uncharged capacitor (see figure below) are C = 1.50 µF, R = 2.30 MN, and E = 10.0 V. R (a) the charge on the capacitor... ...a long time after the switch is closed 900 = ..4.1 s after the switch is closed q = (b) the current in the resistor... ...immediately after the switch is closed In = HA ..4.1 s after the switch is closed I = HA ... a long time after the switch is closed I, = (c) The rate at which energy, 4.1 s after the switch is closed, is... ...being dissipated in the resistor Presistor = ...being stored in the capacitor Рсаpаcitor %3D µW
In an RC series circuit, the EMF, E = 8.1 Volts, resistance = 1.40 MQ and the capacitance = 10.0 µF. Calculate the maximum charge possible on the capacitor in μC. %3D Use 1 decimal place in your answer.

SEE MORE QUESTIONS