Four-bar mechanism with the following available link lengths: r1vertical = 0.433, r1horizontal= 0.7, r2 = 0.250, r3=0.7 Determine - 2 - 3 4 The type of mechanism The angle of rocker. The length of rocker.

Q: What is the minimum tension must your cable be able to support without having your sign come…

A: Given data: - The length of the beam is L = 1.60 m. The mass of the beam is m = 20 kg. The mass of…

Q: For condition I: It was given to you to use SAE1040 hot rolled steel project, you select a different…

A: Condition 1 : SAE 1080 is the first condition. Because the characteristics of annealed steel and…

Q: For your final design project, you use a keyway to hold your gear on the shaft. The radius of the…

A:

Q: List 2 double-rocker mechanisms that are used in industry. Justify why each mechanism belongs in the…

A: The two double-rocker mechanisms used in industry are as follows:1.  Bell Crank Lever Mechanism:…

Q: An SAE 1040 Cold Drawn Steel part has a rectangular shape with dimensions of 2 in  base x 6 in…

A:

Q: Determine the resultant internal loadings acting on the cross-section at point B.

A: The section of the loading up to B from the end c is shown below: The total load acting per feet in…

Q: Shown below is a figure of a landing gear configuration on the VS and VD planes (for landing gear…

A: The given figure shows the landing gear configuration on the VS and VD planes (for landing gear the…

Q: is recreating rolling The large stone columns by animal power and pivot points cut into the center…

A: (a) Draw a free-body diagram of stone column.

Q: Draw Diagram for Deformation of a Circular Bar in Pure Torsion?

A: Twisting of the bar is observed when a torsional load is applied over the bar. An angular…

Q: Shown above is a cord tension tester. Find the tension T in the cord, expressing it in terms of the…

A: The tension in the cord is 4Pcot 10

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.85 in. and a wall thickness…

A:

Q: An SAE3140 OQT 1300 steel bar with a rectangular cross section of  2 in  ( base) by 3.5 in (height)…

A:

Q: Step 1: Given: specific gravity, G=1.7 The objective is to determine: a. density of fluid in…

A: Specific gravity G = 1.7Find(1) Density ρ(2) specific weight ɣ

Q: = 3) A double screw (Acme thread angle o 14.5) mechanism is designed to lift a load of 18,000 lb in…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: At what scale was the original drawing created?

Q: Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN.…

A:

Q: Determine all support and pin forces for the frames listed below. Include force summary table for…

A:

Q: The butt connection shows 8-22 mm diameter bolts(bolt hole dimension of 26 mm) spaced as shown below…

A: dia of bolt=22mmdia of hole=26mmyield stress =248Mpaultimate strength of steel =400Mpa

Q: A part is loaded with a combination of bending, axial, and torsion such that the following stresses…

A: Given:The material properties are .The adjusted endurance limit is .The fatigue stress concentration…

Q: Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia =…

A: Write the given data with suitable variables: P=426 lbdmin=0.1959 in

Q: For each of the structures shown in Fig.2, sketch the following: i. Free body diagrams showing the…

A: Given: FA = 300 lbf FB = 750 lbf

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.