For the system shown in Figure 1 find the range of values of k for which the system is stable by using the Routh - Hurwitz criterion. Assume that the para. c and d' are positive R(s) Y( H 3k S 2a s+d: H s+b S+C

Q: 2) Find: eo(s)/ei(s), if R1=R3=10kohms, R2=R4=100kohms, Cl=C2=10microfarad. R2 C2 R4 ww R3 R1 eo

A:

Q: You have the comparator shown below +Vcc=9V R₁ A Vin + R₂ (-Vcc=0) with the input voltage Vin(t)…

A:

Q: Determine the inductor current it) for both t=0 and t> 0 for the given circuit. Assume V 29 V. V 392…

A: The given circuit isV=29 Volts.We need to find the inductor current i(t) for both t = 0- and t >…

Q: A) Determine the range of K for which the system is stable. K(s + 1) s(s+ 6) (S-1) 1+ B) Determine…

A: A. Need to find the range of k for which the system is stableB. Need to find any of the roots…

Q: To =2+(3090+3090)/1e7 please help me ex7

A: We need to plot  and  in the same plot.where

Q: 2. Solve for the indicated quantities: 12 13 14 0.704 R1 120 KO ET RT R2 200 K R3 180 K2 R4 240 KQ…

A:

Q: For the circult shown, what is the Mesh Current Method equation for mesh D? j2n 20 2+20 1-jn Ic…

A: ANSWER:- OPTION.A

Q: 1. Add the following numbers that are in 2's complement (n=7). Show your work, and convert all…

A:

Q: In the circuit shown in figure, after the switch is open for a long time, it is closed at t=0. Now,…

A:

Q: For the op-amp circuit below connect an 8 ohm resistor in parallel with the capacitor. Suppose that…

A: Given:an op-amp circuit,An 8 resistor is connected in parallel to the capacitor. To find:Zero sate…

Q: Consider the circuit shown below left. ww 100 Ω 5 V SW1 500 mH ww 100 02 ww Rth Vth SW1 a ell 500 mH…

A:

Q: For the circuit in Figure 3 the switch is in the left position for several minutes: (a) Find the…

A: When switch is in the left position for a long time, the capacitor will behave as open-circuit as…

Q: V₁(t) ix(t) R₁ Calculate the energy stored at -0.12 ms: C₁ Problem is related to Problem x.xx in the…

A: Given the circuit R1=8 ΩC1=0.45 μFV1t=5cos2π103t V

Q: Consider the second order model as ë + 3x + 9x = ù + 2u. Draw 3 different block diagrams for the…

A: For the given system we need to draw the block diagram.

Q: (a) 012

A: Note: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: Determine the type of response that is obtained from Figure 4 100 mH 100 V C0.1 µF 4000 Figure 4 a.…

A:

Q: VCE) is (1), R₂ FISCH) 1 C1 1₂. (C) Input → V(t) Output V₂(t) →>>> roon Ri √₂ (107²2 Find state…

A: The given circuit is shown below.The state variables are defined as  and .Note:(i) Here  is current…

Q: Problem 2 (a): Match each ODE to its corresponding step response. All initial conditions are zero.…

A: Given diagrams are,Asked to match the system with corresponding step response.Note: “Since you have…

Q: Solving for R using the Discharging curve equation: V(t) = 1.83V Vc = 4.96V C =4.7uF T = 50s V(t) =…

A: A RC circuit having V(t)=1.83 V.VC=4.96 V.C=4.7μF.T=50s.We need to determineThe value of R.The value…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.