You have the comparator shown below3 PM5R₁Vin [V]R₂0with the input voltage Vin(t) given.+Vcc=9Vis.cpp.edu/courses/50739/quizzes/155206/take/questions/24791670t₁ = 2 s, Vout=Vinot₂ = 4 s, Vout=+t3 = 6 s, Vout=(-Vcc=0)t48 s, Vout=Identify the output voltage Vout at the following times. Data: R₁ = 500 Q, R₂ = 250 0.VVV-o VoutVQuiz: Quiz 06t [s]

Answered: Image /qna-images/answer/105e0783-e69e-4073-b650-2b0b2e77d379.jpg

You have the comparator shown below +Vcc=9V R₁ A Vin + R₂ (-Vcc=0) with the input voltage Vin(t) given. .cpp.edu/courses/50739/quizzes/155206/take/questions/2479167 PM 5 Vin [V] 0 t₂ = 4 s, Vout= t [s] Identify the output voltage Vout at the following times. Data: R₁ = 5000, R₂ = 250 0. t₁ = 2 s, Vout= 13 = 6 s, Vout= V V -o Vout V Quiz: Quiz 06 8

You have the comparator shown below +Vcc=9V R₁ A Vin + R₂ (-Vcc=0) with the input voltage Vin(t) given. .cpp.edu/courses/50739/quizzes/155206/take/questions/2479167 PM 5 Vin [V] 0 t₂ = 4 s, Vout= t [s] Identify the output voltage Vout at the following times. Data: R₁ = 5000, R₂ = 250 0. t₁ = 2 s, Vout= 13 = 6 s, Vout= V V -o Vout V Quiz: Quiz 06 8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a Schmitt trigger circuit with + VSAT = + 12 V, VUT = 4V, and V = 0 V. This circuit is modified to be an oscillator circuit by adding C = 3.948 uF and R = 4 KQ. The charging time ( T) of this circuit is %3D LT %3D ch Select one: a. 1.6 msec b. 3.2 msec C. 4.8 msec d. 6.4 msec
Q5/ Design a Colpitts oscillator as shown in figure below with 10 MHz output frequency. Find the values of C1, C2 and L1, then plot the waveforms at points P1 and P2. +Vcc R1 R4 P2 Cout Q1 Cin P1 R2 Re * Ce 升C1 * C2 Colpitts oscillator www.circuitstoday.com Your answer Q6/ Design a delay circuit using the IC 555, such that the delay between input and output to be 2 minutes. Draw the input/output waveforms. العربية الإنجليزية
Determine the required values of R1, R2, Rc, and RE. Also, determine the expected output voltage if the input voltage is equal to 0.001 Vrms. GIVEN: Zi = 1145.66 ohms Zo = 3.3 Kohms Beta = 80 Vcc = 20V R1 + R2 = 43.7 Kohms Av = 167.43 Ai = 58.13
Transform and draw the equivalent small signal circuit model using ONLY theHYBRID-PI model.
Prob 1: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vh1 Vh2 are dc voltage sources, and Il is an ideal dc current source. Ignore body effect for all problems. Vino- M3H M₂ VDD (a) →Vb3 Vb2 Vout M₁ →Vb1 J HE VDD M3 (b) - Vout VinM₂ 4M₁ J VDD M3 VinM₂ 4M₁ (c) Vout
I need answer in your hand Design a buck-boost converter to supply a load of 100 W at 60 V from a 30 V source. The output ripple must be no more than 2 percent. Specify the duty ratio, switching frequency, inductor size, and capacitor size.
Please do fast ASAP
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Problem 9.63 , except with R=1kOhm and a 100 Ohm load resistor from the op amp output pin to ground. Also find iofor each set of input conditions.
Q. An Oil and Gas Company has gave us a contract to design a temperature measurement instrument The instrument has to measure temperatures between 0 to 100C using RTD PT100 1- The Wheatstone bridge must be leaner and proportional 2- Wheatstone bridge must start from zero volts Design the instrument if you know the following The resistance of the RTD PT100 is =100 Ohm's at 0°C and 139.5 Ohm's at 100°C the input of the circuit is 5V and the output is 0.1V Given the following table is the reading of the instrument for some temperature values when R1=R2=R3=100 Ohm's Temp Vout 20 0.11 40 0.19 60 0.30 80 0.36 100 0.41
Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max) = 100 mA. Design a parallel regulator to yield a regulated output VOUT = 5.0 V. 10 V VINO VREF R₂ VEZDI www R₁ b) 0.5 W, 50% c) 1 W, 25% d) 1 W, 50% e) None of the above 2₁ a www Ry Vx 5 ΚΩ VouT 5V What is the rating (in Watts) for R₁ and efficiency of this linear regulator? a) 0.5 W, 25%
Question 1: a) Sketch Vo versus time for the circuit shown with the input given. b) Determine DC output voltage without a capacitor. c) If a capacitor of 10 uF is placed in parallel with RL, sketch the vo versus time. d) find the DC output voltage. Given R1 = R2 = RL = 2.2 k2. Vi +40 D1. D2 10 ms R = 2.2 k2 ww R%3D 1GF R = -40 2.2 k2 2.2 k2