For the switching converter shown in the following figure, assume steady- state operation. Also assume that the components are ideal, the inductor current is always positive and continuous and switching period is Ts. If the voltage VL is as shown, calculate the duty cycle of the switch S.

For the switching converter shown in the following figure, assume steady- state operation. Also assume that the components are ideal, the inductor current is always positive and continuous and switching period is Ts. If the voltage VL is as shown, calculate the duty cycle of the switch S.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=200 Volts, Time period is 5 milli seconds and 0 =40 degrees. Vp t = 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms = b) Angular frequency =
3. A three phase bridge rectifier is supplied by 380 Volt line voltage through a Star/delta connected transformer of which turns ratio is 1. The firing delay angle is a=30° and the load is resistive R=2.2 Ohm. Draw the circuit diagram and mark the followings on this figure : average values of output voltage, the currents and voltages of each transformer leg.
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and o =30 degrees. Vp t= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.8 ms b) Angular frequency =
I need the answer as soon as possible
give an example of AC to DC converter diagram
2. A C-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm². Next find the flux flowing thru the C-core.
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). VOlvolt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. V(p.P) = 0.1 V 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) T = 0.01 sec. → t(sec.)
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
What is easier to smooth single-phase or three-phase rectifier circuits? And why?
A 220 V, 1 kW heater is fed from a single phase ac voltage controller using a thyristor in anti-parallel with a diode. If the firing angle is 45°, sketch the circuit and: a. Calculate the output voltage and current.b. Sketch the output voltage and current waveforms.c. Calculate the load power.d. Calculate the average current through the load
A sinusoidal voltage has a value of 100 volts at 2.5 milliseconds and completes one cycle.It takes 20 milliseconds. Then find the maximum cost and the time to reach it for the first time
With explanation