For the split ring shown, determine the stress at point A and at point B. Take P= 1700 kN.90 mm40 mmBPThe stress at point A is 758.914 mmMPa.The stress at point Bis -33.7 ✪ MPa.

Given: P = 1700 KN D1 = 40 mm D2 = 90 mm W = 14 mm To find: σA and σB

Answered: For the split ring shown, determine the…

Engineering

Mechanical Engineering

For the split ring shown, determine the stress at point A and at point B. Take P = 1700 kN. 90 mm 40 mm B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The joint is subjected to a force of P = 2-- lb and F = 150 lb. Determine the state of stress at…

Q: A plate with a width of 300mm and thickness of 20mm is to be connected to two plates of the same…

A: Given: Width of plate w=300mm t=20 mm rivet diameter d=25 mm hole diameter dh=28.2 mm

Q: the state of stress at points A and B, and show the results on a differential elements located at…

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: Determine the torsional stress in the thin-walled tube as shown:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

Q: Take the section AB, construct the FBD and label the internal loadings, determine the normal stress…

Q: The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and…

A: Using similar triangle approach Here, the length and area of both of the rods are the same.

Q: A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads.…

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

Q: (e) E = бу 30 MPa Txy 85 MPa Ox 120 MPa = =

A: GivenPart eσx=-120MPaσy=30MPaτxy=85Mpa part fσx=30MPaσy=-80MPaτxy=15Mpa

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: The small steel plate is connected to the right angle bracket by a 6 mm diameter bolt and the…

Q: Q3) Show the state of stress at points A and B on the assembly at section 400 mm а-а. a 200 mm AB…

A: Write the given data: The load in the x-direction will produce twisting couple on the vertical…

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 69 kN if it…

A: Given: Here is the given data, Axial force, F=69 kN Stress, σ=28 MPa dido=26 To find: The outer…

Q: Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of…

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: The solid circular rod has a cross-sectional area of 450 mm². It is subjected to a uniform axial…

Q: The screw of the clamp exerts a compressive force of 500 lb on the wood blocks. Determine the…

A: Area at section (a-a) Moment of inertia at section (a-a)

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

Q: The beam is subjected to the load at its end. Determine the maximum principal stress at point B.

A: Determine normal stress due to axial load Due to shear load there will be bending moment at B…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a–a.…

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: If F1 = 1070 Ib and F2 = 2095 Ib, determine the magnitude of the normal stress produced at point H.…

A: Given: The force, F1 = 1070 lb The force, F2 = 2095 lb

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 34 kN if it…

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: Given bar having cross-sectional area of 700mm^2 is subjected to axial loads at the positions…

A: Given data: A=700 mm2 Need to determine the stress in segment QR.

Q: Solve using Mohr's circle

A: For the given state of stress, To find: The normal and shearing stresses after the element has…

Q: Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches…

A: Given data: Weight of the bar, W = 6000 lb. Cable diameter, d = 0.6 in. Draw a free-body diagram…

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w) = 10 lb-ft the FBD of the cut segment of the rod is…

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

Q: The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the…

A: Given data

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.0…

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

Q: 1- The cross section of the machine part is a square, 5 mm on a side. If the maximum stress at…

A: According to the given information, the side of the square is 5 mm and the stress is 150 Mpa. The…

Q: The beam supports the loading shown. Determine the state of stress at points E and F at section a-a.

Q: 02. The wood pole is supported by two cables of ¼-in diameter. The turnbuckles in the cables are…

A: Tension in cable induced compressive stress in the Pole. For smallest permissible diameter of pole ,…

Q: Assume that the magnitude of the vertical force P is 2.5 kN. Determine the stress at point A and B

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

For the split ring shown, determine the stress at point A and at point B. Take P= 1700 kN.
90 mm
40 mm
B
P
The stress at point A is 758.9
14 mm
MPa.
The stress at point Bis -33.7 ✪ MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1:

VIEW

Step 2:

VIEW

Step 3:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the normal stress at A and B if the blade of the coping saw has a tension of 40 Newtons. Ans: 123 MPa @A, 62.5 MPa @B 8 mm 75 mm 1A 3 mm 8 mm 3 mm B 100 mm 50 mm
4. The shaft below is hollow from A to B and solid from B to C. Determine the maximum shear stress in the shaft. The shaft has an outer diameter of &0mm and the thickness of the wall of the hollow segment is 10mm. Please note there are two different formula for solid and hollow shaft. 4 kN-m 2 kN m
Given the plane element shown which is an element acted upon by combined stresses. a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's Circle determine the maximum normal stress on the element.
The vertical links (at BD and CE) have a thickness = 5.4 and width = 31.2 mm uniform rectangular cross section. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E and choose the correct options. Applied load is 18.9 N, diameter of the pin is half of the width. All the options have been rounded off to two decimal places. 0.4 m 0.25 m 0.2 m O a. The stress in member BD is =0.18 MPa O b. The stress in member BD is =0.09 MPa O c. The stress in member BD is =-0.07 MPa O d. The stress in member BD is =-0.14 MPa O e. The stress in member CE is =-0.04 MPa O f. The stress in member CE is =-0.07 MPa O g. The stress in member CE is =-0.18 MPa O h. The stress in member CE is =-0.18 MPa
FI3-2 Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. 400 kN Fasm- 300 mm 100 mim 100 mim Section a
QUESTION 1 Force F= 4 kN and length a = 5 m. The radius of the bar is 0.09 m. Determine %3D • the internal loading at the section shown • the state of stress at point Cand show the result on a volume elemen located at this point. A C 1 m 1 m
The solid rod is subjected to the loading shown. Determine the state of stress at point A, and show the results on a differential volume element located at this point.
Determine the normal stress developed at points A and B. Neglect the weight of the block.
The aluminum tube is subjected to a torque of M = 2 kN m. Determine the average shear stress in the tube if the dimension a = 200 mm. Each side has a thickness oft = 6 mm. Give the answer in the box in MPa with one decimal place. (ANSWER NEATLY AND ASAP ONLY IF CORRECT)
In each case, the state of stress sx, sy, txy produces normal and shear stress components along section AB of the element that have values of sx = -5 kPa and txy = 8 kPa when calculated using the stress transformation equations.Establish the x and y axes for each segment and specify the angle u, then show these results acting on each segment.
Determine the principal stress and absolute maximum shear stress developed at point B on the cross section of the bracket at section a-a. Show the Mohr's circle for point B. -300 mm 150 mm 2.5 kN a 12 mm B 6 mm www 6 mm 5 4 A, 36 mm'36 mm Section a - a 6 mm
I need the answer as soon as possible