For the sinusoidally modulated “DSB-LC" waveform shown in the Fig. below Find : • Find the modulation index. • Sketch a line spectrum. • Calculate the ratio of the average power in the sidebands to that in the carrier. • Determine the amplitude of the additional carrier which must be added to obtain a modulation index 20%

For the sinusoidally modulated “DSB-LC" waveform shown in the Fig. below Find : • Find the modulation index. • Sketch a line spectrum. • Calculate the ratio of the average power in the sidebands to that in the carrier. • Determine the amplitude of the additional carrier which must be added to obtain a modulation index 20%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q 2 :J An audio signal given by 15sin(4000pi * t) + 20sin(8000pi * t) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60sin(100, 000pi * t) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why? to
digital communicationA signal was represented using Bipolar RZ with a bandwidth of 40 kHz, then thebandwidth will be …………. If Bipolar NRZ was used.
-The modulating signal 2cos (2 π×103 t) is used to modulate a carrier signal 40cos (2 π×104t). Evaluate the modulation index, percentage modulation, frequency of side band components and their amplitudes .What is the bandwidth of a modulating signal.
(1-4) A sinusoid of the frequency 2100 Hz is sampled at the rate 8/7 samples per baseband cycle. (a) In time domain, draw one cycle of this sinusoid, the corresponding samples, and the reconstructed signal. What is the frequency of the reconstructed signal? (b) In frequency domain, draw this sinusoid, the corresponding samples, and the reconstructed signal. ?. (1-5) The signal r(t) = 100 sin(100)+75c(100m) in
For an FM modulator with 48 kHz of frequency deviation. and a modulation signal frequency fm= 8kHz, determine the bandwidth using both the Bessel table and Carson's rule.
A receiving antenna picks up 50 micro volts of signal. The transmitting antenna switches to a nearby antenna which has a 5 dB gain over the original antenna. How much of the new signal is picked up by the receiving station? Show the calculation in detail.
Communivations
3. In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.
Type your question here in the certain phase-shift-type SSB generator, the phase shift for the modulating signal is somewhat different from 90o . Find the ratio for the undesired sideband amplitude. Also, compute its value when the phase shift is 80 instead of 90 .
solve only question 1.b 1.a) Calculate the bandwidth and baud rate for an FSK signal with mark frequency 34 kHz, space frequency 26 kHz, and input bit rate 2 kbps. Use the calculator for bandwidth. 1.b Using a table of Bessel functions, determine the minimum bandwidth for the FSK signal from the previous problem (Problem 1.a). Remember that the significant bands are taken for those with amplitude > 1%. Since the table is normalized (Jo=1 at most), the significant sidebands are those with amplitude > 0.01). -- Indications: In your answer, place the result without the units and expressed in kilohertz
Determine the power of the signal Asinwt.
Question 3 (a) Briefly explain THREE (3) disadvantages of Single Sideband (SSB) over Double Sideband Suppressed Carrier (DSBSC). (b) An AM DSBSC signal with a load resistance 50 2 has the following equation: VaMt) = 8 sin 21.53 x 10°t sin 11.88 x 10°t (V) i. Calculate the upper and lower sideband frequencies. ii. Determine the bandwidth. iii. Calculate the total power. iv. Sketch and label the resultant frequency spectrum. (c) An AM DSBFC signal has a carrier frequency of 300 kHz with peak amplitude is 17 V. The modulating frequency is 15 kHz with peak amplitude of 6 V. i. Determine the peak amplitude of the modulated sidebands. ii. Calculate the maximum and minimum amplitude of the envelope. iii. Sketch and label the resultant frequency spectrum. iv. Sketch and label the modulated signal in time domain.