For the rotational system shown in Figure P2.19, find the transfer function, G(s) = 62(s)/T(s). [Section: 2.7] 1. |N = 4 D,=I N-m-s/rad N2 = 12| FO =2 kg-m )½ = 1 kg-m?- |N3=4 D2 = 2 N-m-s/tad N4 = 16 D3 = 32 N-m-s/rad K= 64 N-m/radg )s = 16 kg-m³0O00 FIGURE P2.19

For the rotational system shown in Figure P2.19, find the transfer function, G(s) = 62(s)/T(s). [Section: 2.7] 1. |N = 4 D,=I N-m-s/rad N2 = 12| FO =2 kg-m )½ = 1 kg-m?- |N3=4 D2 = 2 N-m-s/tad N4 = 16 D3 = 32 N-m-s/rad K= 64 N-m/radg )s = 16 kg-m³0O00 FIGURE P2.19

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
diagram, F, is the input force exerted on the cart by the voltage applied to the motor, m, is the mass of the cart. The encoder is used to keep track of the position of the cart on the track. Cart Encoder Mater March 7, 2023 Track X Figure 5: Free body diagram of the cart (ignoring friction) Using Figure 5 and basic Newtonian dynamics you can derive the equations governing the system. 3.3 Motor Dynamics The input to your system is actually a voltage to the cart's motor. Thus, you need to derive the dynamics of the system that converts the input voltage to the foren exertal on the cart. These are the dynamics of the motor. Figure 6 shows a diagram of the electrical components of the motor. Figure 6: Clasic armature circuit of a standard DC motor For this derivation of the motor dynamics we assume the following: • We disregard the motor inductance: IR, so we can use the approximation 0. • Perfect efficiency of the motor and gearbox: -- 1. The torque generated by the motor is proportional…
Please help me solve no. 2 below. Please provide a clear and readable solution. Thanks in advance!!! The course subject is Feedback and Control System. NOTE: The lesson is ROTATIONAL MECHANICAL SYSTEMS.
penaulum shown in the figure, the nonlinear equations of motion are given by where g is gravity, L is the length of the pendulum, m is the mass attached at the end of the pendulum (we - 0. assume the rod is massless), and k is the coefficient of sin e friction at the pivot point. a) Obtain a state-variable representation of the system. b) Linearize the dynamics and obtain a state-space representation of the system around the equilibrium position @ = 180 degrees, ở = 0. Pvor point Llength c) A constant torque, in counter-clockwise direction, is applied as an input to the pendulum. Angular position is the measured output. Derive the transfer function from the torque to angular position for the linearized pendulum system obtained in part b). Massles rod m, mass
Consider two robot-manipulators:• A SCARA robot with joints displacement range q1,2 = −90◦...90◦ and q3 = 0..10cm and links lengths L1,2=10 cm.• A Cartesian robot with joint displacements’ range q1,2,3 = 0..10 cm.Which statement is correct?1) The Cartesian robot has a larger workspace.2) It is not possible to judge the workspace based on the information provided.3) Both robots have revolute joints.4) The SCARA robot has a larger workspace.
mm.2
Chapter 19, Problem 54P, part task bI think there is an error in part task b. It is not clear how to find the final expression for T_max.After it has been made clear that T_max = T_3, there is a description (See blue square in the attached picture part task b) which describes that an expression must substitute T_1, but the written expression applies to T_3?In the calculation after this, there is a sudden jump to the final expression for T_max. But it's not clear how I'm going to get to the final expression? (The orange square in the attached picture of part task b) I have includet pictures from: The task descriptions. Expert sulution to part task a, where we are given the expression, that is needet to solve part task b. And expert sulution to part task b
Answer letter a only.
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)
How do you interpret a continuously rising or falling angular position output in Simulink
Learning outcome Fundamental.4 evaluation For the problem related to Fundamental.4, a sketch of the considered system showing and naming (or numbering) every part of the system considered, the respective velocity and acceleration of each, and the frame of reference considered is mandatory. Its absence will automatically make the problem false. At the instant observed below 0 =34°, =9°. 3 ft 2 ft 0 $ A WAB B What must be the angular velocity of the link AB, WAB in rad.s¹ if the linear velocity of C is 4 ft.s¹¹
A slider-crank mechanism is required to do the following crank angle-slider position coordination. Crank Angle (Q) Slider Position(S) Position-1 0° 12 cm Position-2 90° 10 cm Also at position 2, the speed of the slider will be 5 cm/sec leftwards as the crank is rotating CCW by 1 rad/sec. Then verify your design by drawing your mechanism at crank angles 0° and 90° and measure slider position and see if they are 12 cm 10 cm respectively. If so, proceed with a velocity analysis at second position, assuming that crank has a speed of 1 rad/sec CCW and find the slider speed , check whether it is 5 cm/sec leftwards or not.