For the requested latch types, do the following: • Derive the characteristic equation for Q+ in SOP. • Show the latch gate structure by adding to and/or changing gates of the SR-NOR-Latch. (a) SR-NOR-Latch-with enable (b) Set-dominant SR-NOR-Latch (SR=11Q+ Q+ = 1) (c) Reset-dominant SR-NOR-Latch (SR = 11 ⇒ Q+ = 0) (d) D-latch with enable (E = 1 ⇒ Q+ =D; otherwise Q+ = Q)

Q: Problem 17. We are comparing to COTS ADCs (Commercial Off-The-Shelf Analog to Digital Converters).…

A: For unit B the ENOB is 8.8 bits and unit B is a 9-bit ADC.We need to calculate the SINAD for unit B.

Q: Q3: what is the output of the successive-approximation register SAR of the Successive- Approximation…

A: We need to find the output of the successive approximation ADC in which analog input voltage given…

Q: Carry generate (G) and carry propagate (P) are defined as follows: G =AB and P = A  B.  a) Show the…

A: The truth table of a full adder is given by…

Q: Q2 Draw the schematic circuit for a resistively loaded NMOS inverter and the relative voltage…

A:

Q: Q2/B: A convolutional code is described by g₁=[ 1 1 0], g2=[ 0 1 1], g-[111] a. Draw the encoder…

A:

Q: Refer ot the BCD-to-2421 code converter. Use asimilar design procedure to develop the circuit of a…

A: A Binary-Coded Decimal (BCD) converter is a digital circuit that converts a binary number into its…

Q: For the following circuit please find the small signal Input resistance in Ohms [Select] the Output…

A:

Q: 1. Provide a block diagram and a function table for the NOR-Gate Latch. 2. Describe, with the aid of…

A:

Q: A discrete-time sample is equal to -0.35. Using a 2-bit truncation quantizer (with range between…

A: As we know that a n bit quantizer will have 2n number of quantization  levels. So here also for 2…

Q: 2. The following circuit represents a 3-bitlinear-feedback shift register (LFSR). Find the counting…

A:

Q: Given this R-2R 4-bit DAC, with R=1kOhms, a. Draw the simplified version with one equivalent…

A:

Q: Q2: A 4-bit shift register with the feedback connections [4.3.2.1) ar condition [1,0,0,1).(a) Draw…

A: 4-bit shift register with feedback taps [4,3,2,1]  Block diagram Initial condition: 1001…

Q: ind the value of the resistors, the voltages of VG. VS, VD, VDS AND ID.

A: According to the question, for the given JFET circuit as shown below We need to find the value of…

Q: 2. The 2-to-4 decoders with active-low outputs are available as building blocks. Each block has two…

A:

Digital to Analog Converters

Digital to analog converters are commonly known as DAC, digital analog converter, D2A, or Digital-to-Analog converters. DACs are one of the important devices used in the electronics and electrical domain. DACs are the systems that convert a digital signal into an analog signal, whereas an analog to digital converter or ADC performs the opposite function. Digital signals are those signals that can represent the information or data as a set of discrete values. At a particular instant of time, a digital signal can only take a particular value of data. A digital signal is characterized by two unique values; zeros and ones, or true and false, represented by the Boolean domain. These are also known as binary signals or logic signals. Unlike digital signals, an analog signal is represented by continuous values, where at any time instant, the analog signal is represented by a real number.