i need the answer quickly For the following system, if the input X[k]= 8(k+ 1) + 2.4k and output Y[k]= 2(k)u[k], the impulseresponse is h[k]= A. k. 2(k)u[k] + B. (k-1). 2(k-1).u[k - 1], so the values of A, B are..X[k]H(z)Y[k]

Answered: Image /qna-images/answer/f9070361-7cc4-4bfb-aff0-e30c49b1d041.jpg

Answered: For the following system, if the input…

For the following system, if the input X[k]= 8(k+1) + 2.4k and output Y[k]= 2()u[k], the impu response is h[k]= A. k. 2(k)u[k] + B. (k-1). 2(k-1).u[k - 1], so the values of A, B are.. X[k] H(z) Y[k]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
For the following switch circuit: A) Derive the switching algebra expression that corresponds one to one with the switch circuit. B) Derive an equivalent switch circuit with a structure consisting of a parallel connection of groups of switches connected in series. (Use 8 switches.) C) Derive an equivalent switch circuit with a structure consisting of a series connection of groups of switches connected in parallel. (Use 7 switches.)
i need the answer quickly
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
I need the complete solution & explanation pls
Select the best answer from multiple choices: 1. The system e'e-5 is: a. Linear, time invariant, casual. b. Non-linear, time invariant, non-casual. c. Non-linear, time varying, casual. d. Not all the above. 2. Noise can be reduced through: a. Increasing So. b. Increasing Si. c. Both (a) and (b). d. Note all the above.
I want to solve both questions please