For the following set of Stadia notes. Rod Interval (m) = 3.23 Horizontal angle = 85° 23' (measured reference to line AB) Vertical angle = + 0° 00' on RR= 1.07 m. Azimuth of AD = 135° 43' Theodolite at A, hi = 1.5 m, and Coordinate of point A is (X= The Z coordinate of point D according to the given data is: 75, Y= 125, Z=525) n

For the following set of Stadia notes. Rod Interval (m) = 3.23 Horizontal angle = 85° 23' (measured reference to line AB) Vertical angle = + 0° 00' on RR= 1.07 m. Azimuth of AD = 135° 43' Theodolite at A, hi = 1.5 m, and Coordinate of point A is (X= The Z coordinate of point D according to the given data is: 75, Y= 125, Z=525) n

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the following: b=360mm d=550mm fc'=35MPA fy=420MPA Mu=700KN-m Determine As USE NSCP 2015, As = sq.mm.
draw the SF and BM diagrams along with qualitative deflected shapes
An instrument is setup at point A, and the rod at B. Elevation of point A is 700meters. Height of instrument is 1.75 meter. Stadia Interval Factor = 100 Vertical angle +10degree Middle Reading + 60 1.75 meters Stadia Intercept M(10) cm Stadia Constant 0.30 Required: Solve for the elevation of B.
Determine the internal efforts in a section E located two meters from the bezel:
The table below is the page of a level field book. Calculate the reduced levels of points C, F and H if the height of instrument (H.I) for the first and second position of the level= 33.1 and 33.5 respectively. Note: the readings inside the brackets (.....) represent inverted .staff reading St. No. A B с le D E F G H I BS (3.4) ? IS (2.7) 0.9 (1.56) (1.9) 2.6 (0.8) FS 0.7 (2.9) C-35.8, F-32.4, H=36.4 C-36.8, F=32.4, H=36.4 C-34.6, F=30.9, H=36.4 C=36.5, F=34.6, H=36.4 C-32.2, F-35.4, H=34.3
For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a roughness coefficient of 0.014 L2 D2 Pipe Length, ft Diameter, in Q₂ 1 980 2 490 Li Di SD₁ n = 0.014 3 250 Qs 4 980 L3 D3 LD 5 1480 Which of the following statements is TRUE? The head loss in pipes 1 and 5 are equal. The head loss in pipes 3 and 4 are equal. The headloss in pipe 2, 3 and 4 are equal. The sum of the head loss in pipes 3 and 4 is equal to the head loss of pipe 2. 88852 15 12 2 points Clear selection
How to calculate preassures in different points?
From the figure shown below determine how many minutes would it take for the water surface in tank 1 be with the same level with the liquid surface at tank 2?
The table below is the page of a level field book. Calculate the reduced levels of points C, F and H if the height of instrument (H.I) for the first and second position of the level= 33.1 and 33.5 respectively. Note: the readings inside the brackets (.....) represent inverted .staff reading St. No. A B с le D E F G H I BS (3.4) ? IS (2.7) 0.9 (1.56) (1.9) 2.6 (0.8) FS 0.7 (2.9) C-35.8, F-32.4, H=36.4 C-36.8, F=32.4, H=36.4 C-34.6, F=30.9, H=36.4 C=36.5, F=34.6, H=36.4 C-32.2, F-35.4, H=34.3
Read: 25m Maximum Minimum CS Scanned with CamScanner 5m w= 8kN/m Tension Tension
In chain and compass traversing, the magnetic bearings of the survey lines are measured by a O a. dumpy level O b. chain O c. theodolite O d. compass
PA+ Q3: A traverse line is 152.4m long. If the tape used in the field is (100 ft) when standardized at 63° F what correction must be applied if the temperature at the time of measurement is 73° F? (Assume a= 11.2 * 10-6 per deg C)