For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a roughness coefficient of 0.014 L2 Dz Pipe Length, ft Diameter, in 1 980 2 490 Li Di Ls Ds n = 0.014 3 250 980 1480 L3 D3 La D Which of the following statements is TRUE? O The head loss in pipes 1 and 5 are equal. The head loss in pipes 3 and 4 are equal. The headloss in pipe 2, 3 and 4 are equal. The sum of the head loss in pipes 3 and 4 is equal to the head loss of pipe 2. 2345 88851 12 2 points

For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a roughness coefficient of 0.014 L2 Dz Pipe Length, ft Diameter, in 1 980 2 490 Li Di Ls Ds n = 0.014 3 250 980 1480 L3 D3 La D Which of the following statements is TRUE? O The head loss in pipes 1 and 5 are equal. The head loss in pipes 3 and 4 are equal. The headloss in pipe 2, 3 and 4 are equal. The sum of the head loss in pipes 3 and 4 is equal to the head loss of pipe 2. 2345 88851 12 2 points

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 2: The steel shaft below is part of a mechanical assembly. The shaft is rotating at 125…

A: The rotation of the shaft at target rotation per minute results in the generation of power. The…

Q: Consider two pipes made of same material having diameter D and d and of equal length L. If these…

A: - Diameter of the first pipe ()- Diameter of the second pipe ()- Length of both pipes ()- Discharge…

Q: 1. The represents the roughness of a pipe whereas the Icoefficient accounts for the roughness of the…

A: This question is related to the Fluid Mechanics from Civil Engineering. This question is based on…

Q: Which of the following is a valid potential function for incompressible flow? (Assume A is numerical…

Q: For the pipe network shown in the figure below, what is the flow rate in pipe BA? C O 350 GPM 422…

Q: Which of the following statements are true about major head losses? Select all that are true. Major…

A: Darcy- Weisbach equation is used primarily to find out the major head loses in the pipe due to…

Q: Problem 1: Moody's Diagram - Finding the Friction Factor Value You perform a calculation for the…

A: Given data- Reynold's Number- Re=2.5×105, e/D ratio = 0.0002, To Find- The value of friction factor…

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: A pipe 50 mm diameter is 10 m long and the velocity flow of water in the pipe is 2.5 m/s. What would…

A: head loss is depend on the friction factor, velocity of flow, area of cross section , and length of…

Q: Q1, ( through a filter and then is circulated back to the tanks as shown below. The flowrate is 0.08…

A: Given, Q = 0.08 cfs v = 1.21 x 10-5 ft2/s

Q: 7 A cast iron pipe (roughness = 0.010 in) connects two reservoirs. The pipeline is 1300 ft long and…

Q: The rectangular channel is 2 m wide, and the depth of the water is y₁ = 1.6 m as it flows with an…

Q: Your company will build a water tank to service a building that is 100 ft away with 20 psi water…

A: Pressure required= 20 psi Head required for this pressure = 46.133 ft Distance of service building =…

Q: If oil with a kinematic viscosity of 0.005 ft^2/s weighs 54 lb/ft^3, what will be the flow rate and…

A: To Determine Flow rate, Q and Head loss, hL

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

For the pipe network shown, the flow of water from A to the first junction is 2
cubic feet per second. Assuming all pipes have a roughness coefficient of 0.014
L2 D2
Pipe
Length, ft Diameter, in
Q₂
1
980
2
490
Li Di
SD₁
n = 0.014
3
250
Qs
4
980
L3 D3
LD
5
1480
Which of the following statements is TRUE?
The head loss in pipes 1 and 5 are equal.
The head loss in pipes 3 and 4 are equal.
The headloss in pipe 2, 3 and 4 are equal.
The sum of the head loss in pipes 3 and 4 is equal to the head loss of pipe 2.
88852
15
12
2 points
Clear selection

Determine the velocity of flow in the upper branch, PIPE 2, in feet per
second.
1
Determine the velocity of flow in the lower branch, PIPE 4, in feet per
second.
Determine the head loss in feet in PIPE 2. *
11
*
Determine the head loss in feet in PIPE 3.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The figure illustrates a piping system with three tanks. Determine the flow rate of each pipe using the method taught in class. For each pipe the diameters and lengths are in meters. D1 = 1m L1 = 1000mD2 = 0.5m L2 = 900mD3 = 0.75m L3 = 1200mConsider the roughness e = 0.0003 m and kinematic viscosity of 1.31 x 10^-6 m^2/s
4- Consider the system shown in the figure. If a change of P kPa in the pressure of air causes the brine- mercury interface in the right column to drop by d mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A₂/A₁. P (kPa) d (mm) 6 Sum of last 2 digits of 35 YorkU ID# ending with 0, 2, 4, 6, 8 Sum of last 2 digits of 45 YorkU ID# ending with 1, 3,5,7,9 7 Area, A₁. Air Water Mercury SG = 13.56 Brine pipe SG = 1.1 Area, A₂
Please solve this problem using Moody's Diagram. Aslo, please show the reynold's number that you are getting
2. A large-capacity faucet is to be connected to a water main by 20-mm diameter copper tubing as shown in Figure below. The copper tubing has an estimated f=0.02, and local head losses are created by the corporation stop (C-stop), three bends, and the faucet itself. The faucet exit has a diameter of 12 mm. What is minimum pressure in the water main required to obtain a desired flow rate of 50 L/min when the faucet is fully open? fig1.Faucet connected to water main. Water main Bend 3.5 m C-stop E 2 5m Pipe Bend Bend E Bend 4 m Faucet Fitting C-stop Bend(s) Faucet K 9 1.2 10
Question 10 Which of the following statements are true about minor losses? Select all that apply. Minor losses are always greater than major losses. Minor losses are caused by screens, bends, and valves. Minor losses consider viscous effects in the pipe. We can use the Darcy-Weisbach equation to solve for hL(minor).
C3. Provide solution using the Moody diagram Oil (RD 0.8) with viscosity 0.06 Pa.s flows in a cast iron pipe of length 100m and diameter 120mm. Relative roughness = 0.0031 1. Determine the head loss when the velocity is: 3.2 m/s 2. Discuss and agree upon how could the head loss be reduced. Write your conclusions.
Problem 4: Laminar or Turbulent? Oil (s = 0.85 and v= 1.8x105 m²/s) flows through a 100 mm diameter pipe at 0.5 L/s. Part A Calculate the Reynolds number. Part B Is the flow laminar or turbulent, and why?
The total head loss in the pipe system shown in the figure below is 15 m. Assume f= 0.02 for all pipes. Useful properties of the pipes are given in the following ta Diameter Length Pipes 600 mm 450 m 1 500 mm 600 m 3. 450 mm 360 m 4. 450 mm 480 m 600 mm 540 m 5 1 4. What is the discharge in pipe 1? 2.
4. Three pipes of different lengths and diameters connected in series as shown discharges 160 liters per second. If the roughness coefficient n = 0.012 and disregarding minor losses, determine the headloss in each pipe and the diameter of an equivalent single pipe that could replace all the 3 pipes. B D 450mm-1800m 300mm-1500m 250mm-800m