For the following inspection opening, calculate the correct values for A, A1, A2, A3, A4, A5 The design pressure is 900 kPa.g and the design strengths for the metals of shell and branch are 133MPa  A= a. 3545.24     b. 3354.63   c. 3454.36  d. 3445.42   A1= a. 1377.45   b. 1673.71  c. 1773.82  d. 1534.53 A2= a. 721.63   b. 733.32    c. 718.59    d. 738.93 A3 = a. 600  b. 500    c. 450    d. 550 A4 = a. 211    b. 214     c. 220    d. 216 A5=  a. 346   b. 356   C. 366   d. 336

Q: Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage…

A:

Q: What is the resulting Soderberg's factor of safety of a 1.82" diameter shaft operating under the…

A: Given:Diameter of the shaft, d=1.82 inMean torque, Tm=14.9 kip.inAlternating torque, Ta=3.6…

Q: What can be determined when looking at material 1 and material 2 when comparing hardness values and…

A: Given

Q: A structural support for a manufactured from a circ the cross section of the rc textbook. Condition…

A: given: F=20KN

Q: The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry.…

A: When a material is regularly cycled across a specified stress range, the number of cycles before…

Q: You do a series of tensile tests on plates of a magnesium alloy that have been subjected to prior…

A: Yield strength

Q: 10 units of bulb were tested where the normal lifespan is 100 hours 3 units of bulb failed at 10…

A: Failure rate per hr.

Q: In a twist test on a specimen of radius 3mm and gauge length 78mm, while the deformation is still…

A: Option c is correct.

Q: True or False a) If an accurate value for the notch sensitivity is hard to find, I should consider…

A: 1.If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue…

Q: Q.3 In a bushmandrel system, a bush was turned on a mandrel. The mandrel diameter in millimeter is…

A:

Q: e) Compute the strain hardening exponent at the true tensile stress [take K = ) Quantify ductility…

A: The data is shown in two graphs below: the first depicts the whole stress-strain curve, while the…

Q: How long is the thread at 4B?  What do the brackets around dimension 241 at 3C indicate?

A: It is asked to find the length of thread in section 4B and also the meaning of parenthesis in…

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: The percentage of reduction in area of The final area would be: magnesium tensile specimen was 25%,…

A: Given∆A%=-25L=56mdi=20mm

Q: What is the Weibull modulus of this material? Would you advise the use of a similar material with a…

A: The Weibull modulus is a measure of the material's strength variability. A higher Weibull modulus…

Q: Given the following duty record, how much life is consumed at each stress level? 60 ksi 49 ksi 10…

A:

Q: Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels.…

A: A) the material which will show highest elongation, will show the greatest percentage reduction in…

Q: Brass metal is subjected to a 156 Kgf load, with a 2.23 mm diameter of indenter. The indentation of…

A:

Q: Give the location dimensions to the three (3) Ø.437±.005 holes from C Give the location dimensions…

A: In the given figure, here the datum A, datum B, and datum C make the primary datum reference plane.…

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: What are the geometry features in the picture below? Indicate main geometry and tolerances

A: Geometry Features which mentioned in the Drawing are as below:

Q: Considering Figure 20-8 (textbook), the bending geometry parameter, Sw, for case 2 when b=6 and d=9…

A:

Q: On the left end of this object, the thread note indicates 10UNC. What is the pitch for this thread?

A: The objective of the question is to determine the pitch of the thread indicated as 10UNC on the…

Q: CORRELATION OF %CW to STRENGTH and DUCTILILTY OF STEEL YIELD STRENGTH %EL 550 30% 530 28% 510 26%…

A:

Q: Question 8 Which of the following pressure losses contributes to Equivalent Circulating Dens-…

A: Que.8  The following pressure losses contributes to Equivalent Circulation Density bottom: Correct…

Q: What type of indentor is used in a Brinell hardness test? Select one: O a. rhombus shaped O b. None…

A: Hardness test focuses on measuring the hardness of a specimen by subjecting it to indentations with…

Q: 40)A tensile test specimen has a gage length=3.0 inches and a diameter=  .75 inches. Yielding occurs…

A: Given:

Q: 5. Steel What is the longest length of 14 inch: of 4.2 kips without stretching more than 0.20…

A: Given data  Tensile load = 4.2 kips  Change in length = 0.20 in Diameter of steel barstock = 1/4 in…

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.