Solve all parts or i will dislike the answer For the following circuit:a) Determine the type of the transistor and type of configuration of this amplifierAssuming Bof 100, determine VE, IE, Ic, and VecDetermine g, re, and rSketch ac equivalent circuit (use T model)Calculate the gain AvV= +10 Vb)c)d)R 10 kne)CaCaRe = 5 knV --10 V

Answered: Image /qna-images/answer/03e2ba9c-d8f8-4485-9ab1-4175d47a3ee2.jpg

For the following circuit: a) Determine the type of the transistor and type of configuration of this amplifier b) Assuming Bof 100, determine VE, IE, Ic, and Vc Determine g, re, and r Sketch ac equivalent circuit (use T model) Calculate the gain Av V- +10 V c) d) R 10 k e) Ca Re -5 kn V - -10 V

For the following circuit: a) Determine the type of the transistor and type of configuration of this amplifier b) Assuming Bof 100, determine VE, IE, Ic, and Vc Determine g, re, and r Sketch ac equivalent circuit (use T model) Calculate the gain Av V- +10 V c) d) R 10 k e) Ca Re -5 kn V - -10 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2: For the circuit shown in figure (2), he=100 for all transistors and 1/hobs = 200k2. Find: a. DC values for Ics, Ici. Vez, Ic7 and Vco. b. Ad, A, and CMRR of the difference amplifier. +15v 10KE 100k 1k 10k Q8 Q3 v1 Q7 25k Q1 Q2 14.3k Q5 Q6 Q9 -15v Figure (2)
Q1. The output characteristic of a typical transistor is shown below, where the quiescent point is selected on it. This transistor is used in the bias circuit presented below. Find the suitable values of Rg and Rc to fix the Q-point of the circuit properly. +Vcc = 12 V 12- Is = 70 uA 10- Ig = 60 uA 8- Rc Is = 50 uA Rs 6- Ig= 40 uA 4. Is = 30 uĄ Is = 20 uA B = 100 2- VBE = 0.7 V 0- -2- 2 4 6 8 10 12 14 16 VCE (V) Ic (mA)
6) Consider the following multistage amplifier. Draw the corresponding small signal model. Label, Vin, Vo1 and Vo. Do NOT make any approximations. Do NOT perform small signal analysis with this model. Just draw the small signal model. Show your work! Vin Vcc malli Q1 Re1 Vo1 Vcc ww1. Rc2 Q2 Re2 Vo
Input voltage VI is a DC signal. Do not repost other solutions to similar questions. Thank you.
II.The following figure shows a class AB amplifier. (a) Determine the parameters of dc VB (Q1), VB (Q2), VE, ICQ, VCEQ (Q1), VCEQ (Q2). (b) For a 5-Vrms input, determine the power that is provided to the load resistor, and (c) Draw the output signal +Vcc +9 V 1.0kn D: R 5.0 V rms R2 10 kN -Vec
Kindly choose the best and appropriate answer.
Problem 3: The circuit below is a BJT common collector amplifier. Obtain expressions for both the voltage gain A, = You and the current gain A1 = put. Assume Vin » VBE. Vol (Power supply) To 2 Tin Ic 2 9m 2 Ic VT Rin B www. + vin -VBE RL B 1+³ V BE [te] IC VCE E Tout RL O Vin - VBE + Vout
Consider the JFET amplifier in the Figure below with transistor parameters loss = 6 mA, VGS (OFF) = -3 V and VA = 100 V. Let VDD = 10 V. a) Determine RD and VGs such that ID = 4 mA and VDs = 6 V. b) Determine gm and ro. c) Determine the small-signal voltage gain Av = vo/Vi. VDD Vj + VGS + H + VGS ww + UDS VO
electronics
9. State the relationships of the small signal hybrid- π parameters gm & rn to the transistor dc quiescent values. Draw the small signal model of the adjacent BJT amplifier circuit: Rs=0.5 KQ ww HH Cc Vcc= 10 V R₁ = • 56 ΚΩ www 3 R₂ = 12.2 kQ2 Rc=2kQ - VO RE=0.4 KQ
Hand Calculation: Since you now have the values of R1 and R2 resistors, obtain numeric value of voltage gain Av=Vo/Vi, and numerical values of input and output resistances Ri and Ro. Note that you need to DC analysis first. Do a hand calculation and calculate the DC collector current or IC. This is needed in order to calculate the small signal parameters gm and rπ and in turn to obtain the Av , Ri and Ro Hence, first perform a DC analysis (use the circuit in Figure 1 and take all capacitors open) and assume your transistor has a β=140.
(b) For an n-channel, JFET amplifier circuit given in Figure (b), the VGS(OFF) = -6 V, the IDss = 6 mA, and the VGS = 0 V. The drain supply voltage, VDD; = 30 V, is larger than the pinch-off voltage, VP (VGS(OFF)] = [VP), so that the transistor operates in the saturation region. Determine the following: i) the drain current, ID; ii) the drain-source voltage, VDs; iii) the drain voltage VD; and iv) the source voltage, Vs. VDD-30V VGS-OV RD =3K ID + VDS Rs=1k Figure Q(b)