What is the value of the resistor shown below in ohms? Don't use scientific notation.

Q: *Experiment No. 6: Comparator Circuit 1-.What is the pin number of the IC comparator output signal…

A:

Q: Make a table of values that shows all calculations with the switch on verses the switch off. Make…

A: According to the datasheet of 2N3904,  Case 1 when a switch connected to the positive terminal of…

Q: 4. For the following circuits sketch the output vo +8 V لسوري 2.2 ΚΩ 3V

A:

Q: 16 Determine the current at LED, D2. (assume LED forward voltage is 2.1 volts) * R2 1K 5V D1 R1 D2

A: The solution is given below

Q: 5. For the following circuit sketch the output of vo 10 ΚΩ Vi 10 V K -10 V 16 5.3 V- Si 7.3 V- +

A:

Q: What is a Semiconductor? Explain the properties of a Semiconductor such as its physics, etc?…

A: There are various kinds of materials depending on the properties of these materials. In electronics…

Q: I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards…

A: According to the question we need to design a wooden train that runs on wooden track.What's the…

Q: Q.52 A limit switch is illustrated by drawing a wedge shape on the movable contact of a switch…

A: A limit switch is illustrated by drawing a wedge shape on the movable contact of a switch symbol.…

Q: 6. What are the features of LEDS over conventional bulbs? Name some applications for LEDS. A vello…

A: Let us have a look at some of the features of the led. 1. In the case of an led as the name suggests…

Q: 3. For the following circuit find the value of I, and V +16 V 0 Si Si 4.7 k2 Si

A:

Q: Build a thermostat using Arduino Uno, LCD display, temperature sensor and few LED's. Write a program…

A: given Data:

Q: Please answer the two questions, and in the other picture are the drawing we had made. (Which are…

A: Given: Consider the figure (that shows the schematic symbol(types) of electrical loads, switches,…

Q: 1. For the following circuit find the value of the current ID, and the voltage V +8 V 1.2 ΚΩ lp •…

A:

Q: 3. For the following circuits sketch the output vo +8 V -8 V + 16 m 1 KQ Si 4 V

A:

Q: Find the detector current id in the unbalanced Whetstone bridge shown in the figure below. You may…

A: Given, The circuit diagram,

Q: An AC ammeter is connected in series with the primary winding of T1. What is the expected current…

A: The output RMS value of output voltage is as=8.48 voltsThe RMS current measured by the ammeter

Q: 1.Draw an example Turn-on Snubber circuit and explain its working principle and what it is used for.…

A: (1) It is asked to draw a turn-on snubber circuit and also asked to explain its working principle.…

Q: 2. for the following circuit sketch the output voltage vo. 100 V A -100 V Ideal diodes 2.2 ΚΩ

A:

Q: Q1: Two resistors at temperature T are connected to an ideal capacitor as shown below: a) Derive an…

A:

Q: How could we add a third and fourth LED (with resistors)? How would we add more switches?

A: LED stands for Light Emitting Diode. It is a semiconductor device which emits light when current…

Q: - input output transistor MOSFET 1608 output potentiometer

A: Connect the gate terminal of the MOSFET to collector terminal of the transistor and this combination…

Q: I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would…

A: According to the question, an O-gauge track and would like to convert it into a “sensored” track.…

Q: Q.  What will be the status of switch S1 and S2 for which the LED glows. The circuit diagram is…

A: The logic gate based circuit design can be analyzed by forming the truth table. The LED will glow…

Q: 4. For the following circuit find the value of Vo1, Vo2, I Voy + 1kQ w 20 V 0.47 k Si m Si

A: In this question,  We need to determine the voltage Vo1  , Vo2  and current I as shown the circuit..…

Q: Question 1 A microcontroller is used to control three LEDS in series (Blue, Red and White). Assume…

A: Here, we have asked to design an interfacing circuit to control three LEDs connected in series,…

Q: Summarize on how testing is carried out on isolators and circuit breakers of high voltage system.…

A: The Electric power demand is rising rapidly. Now a days, Huge quantity of electrical power is needed…

Q: Problem 3: 100 Use Nodal Analysis to find the output voltage v, in the following circuit. (HINT:…

A:

Q: What is the relationship of the current-voltage characteristic and the color of the Red, Yellow,…

A: Energy Band Gap :The lowest energy is required by the electron to release from the valence band to…

Q: 1. The letter designation SL on an electrical draw- ing indicates a a. limit switch b. low-voltage…

A: As per our policy, i am attempting first question. The letter designation SL on an electrical…

Q: The voltage and current at the terminals of the circuit element in (Figure 1) are zero for t <0. For…

A:

Q: Q2/A- what are the main cases of insulator failures? B-what are type testing of insulator?

A:

Q: *Explain the process here; how to determine the resistor value using the color coders and nominal…

A: Color code of the resistor: Gold and silver color denoted the 5% and 10% tolerance respectively.

Q: Let’s assume that in these two pictures, the batteries in the remote control in picture 1 are…

A: The given image of two remotes are shown below. In these two pictures, the batteries in the remote…

Q: 2. for the following circuit find the value of the current I. Si 1092 Si H₁₁ ' 20 Ω 20 V 4|1|*

A:

Q: 6. The circuit shown below find: (a) Ioa and VpsQ (b) VDs and Vs 14 V 오 1.2 k2 IDss=6 mA VP =-4V DSS…

A:

Q: 1. For the following circuit find the amplitude of the input voltage which results in Vac = 2 V…

A: Given: For the following circuit: To find: The amplitude of the input voltage which results in Vdc…

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.