For the figure shown, the electric motor exerts a (12 kip.in) at E. Determine the shearing stress on the shaft AB knowing that the bearing A is frictionless. What is the angle of twist of disc C relative to disc D? The length of the solid shaft CD is 1.2ft and its modulus of rigidity is 11.2*10 Psi. E 5 kip in. 4 kip - in. D 2.25 in. 3 kip in. 2 in. 1.75 in. A 1.50 in.

For the figure shown, the electric motor exerts a (12 kip.in) at E. Determine the shearing stress on the shaft AB knowing that the bearing A is frictionless. What is the angle of twist of disc C relative to disc D? The length of the solid shaft CD is 1.2ft and its modulus of rigidity is 11.2*10 Psi. E 5 kip in. 4 kip - in. D 2.25 in. 3 kip in. 2 in. 1.75 in. A 1.50 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum shear stress in the shaft and the rotation of end gear A with respect to fixed support E 40 Nm 280 Nm 05 m 150 N m 100 m 04 m (a)
Determine the value of torque T if the total angle of twist is 4.5o.
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
The turbine develops 150 kW of power, which is transmitted to the gears such that C receives 70% and D receives 30%. The rotation of the 100-mm-diameter A-36 steel shaft is a 750 rev/min. The journal bearing at E allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Figure 1 of 1 Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Tax Value Submit Part B $8/0 Submit Request Answer Determine the angle of twist of end E of the shaft relative to B Express your answer using three significant figures. Provide Feedback VAX Units Request Answer ? Ivec 4 ? rad
A hollow steel shaft with an outside diameter of 41 mm and a wall thickness of 9 mm is subjected to a pure torque of T = 6300 N-m. The shear modulus of the steel is G = 87 GPa. Determine: (a) the maximum shear stress T in the shaft. (b) the magnitude of the angle of twist o in a 2.4-m length of shaft. Answers: (a) = i MPа. (b) p = i
With the torques shown and the value of G= 9543 ksi. What would the diameter need to be of the shaft in order to make sure that the the top end of the two cylinders is not allowed to twist by a degree of greater than 1.5 deg. Torque 2-)5 1614 Torq ue 1 217516/6t 3,354 4. 35FA
The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip٠in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel.
The allowable shearing stress is 15 ksi in the 1.5-in.-diameter steel rod ABand 8 ksi in the 1.8-in.-diameter rod BC. Neglecting the effect of stress concentrations, determine the largest torque that can be applied at A
Under normal operating conditions, the electric motor exerts a torque of 2.4 kN·m on shaft AB. Each shaft is solid with diameter d 52 mm. In order to reduce the total mass of the assembly, a new design is being considered in which the diameter of shaft BC will be smaller. Determine the smallest diameter of shaft BC for which the maximum value of the shearing stress in the assembly will not be increased. The smallest diameter of shaft BC is mm.
A composite shaft is comprised of an inner solid steel shaft 1/6 ft in diameter slipped over with a hollow bronze shaft of 1/4 ft outer dimater and 1/6 ft inner diameter and of the same length as the steel shaft. The two shafts are then fastened rigidly together at their ends. For steel, G = 12 × 106 psi, and for bronze, G = 6 × 106 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 12,000 psi in the steel or 8,000 psi in the bronze?
Determine the maximum shearing stress in MPa of a helical spring composed of 20 turns and 19 mm wire diameter on a mean radius of 75 mm when the spring is supporting a load of 1000 N, assume the modulus of rigidity of 83 GPa.