For the figure shown below, compute the normal force in section 1. Neglect the weights of the member. Notethat point B is pin-connected.50KN...5m50C5m5m96 minutes remaining A) 18.66 kNB2.66 kNC13.66 kND6.66 kNE43.66 kNF) 33.66 kN3.66 kNH.23.66 kN

Answered: Image /qna-images/answer/69c03657-7e3c-4468-88d9-9af823548620.jpg

Answered: For the figure shown below, compute the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The Steel rod. E = 210 GPa, has a diameter of 35 mm. If it is subjected to the forces shown, determine the displacement (mm) of the end Cwith respect to the fixed support at A. 30 AN 90 N 30KN 60mm
8.
3 mm- 4. The cross section of the steel tube (G = 11 x 106) as shown carries a 50 kip-in torque. Calculate (a) the maximum shear stress and (b) the angle of twist per foot of length. Use 2 decimal places in every solved value. mm 2mm mm 3 mm mm- 8 2 of 2
ID No:.. Name: Use the method of virtual work and determine the maximum allowed load P so the maximum horizontal displacement of point C should not exceed 5 mm. Each steel member has a cross-sectional area of 1200 mm?. E=200 GPa. 4 m 3 m
Please answer in complete solution and draw an fbd.Note: Please use the second picture as guide for the formulas. Thanks°
120 mm 30° F= 210 N y 1. L--x 150 mm The 210N force is applied to the end of body OAB. If e= 55-degree, determine the equivalent force-couple system at the shaft axis O, in Nm.
Q1: - For the frame shown in figure 1 below is subjected to two forces ( P=20 kN and Q=30 kN). Neglecting the weights of the bars, determine all forces that acting on each of the members. Use the two-force principle wherever applicable. 2 m 2 m B. A 60° D. 60° 4 m 2 m
SHOW FBD DIAGARM
When the three forces acting on the quarter-circular plate are replaced byan equivalent force-couple system with the force acting at point D, the resultantcouple is zero. Determine P and the angle θ.
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2.
PAGE:. DATE :.. A rectangular lot steei tape which was later found to 5 mm too short. The recorded dimensions was mearured uring a be 121.5m long by 92:5m wide. What ir the Were error in the area

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

For the figure shown below, compute the normal force in section 1. Neglect the weights of the member. Note that point B is pin-connected. 50KN ... 5m 60° C AG 5m 5m 96 minut