For the circuit below, Vs = 45V, R1 = 120, R2 = 30, R3 = 90, R4 = 320, R5 = 160, R6 = 3 With R4 as the load resistor use the Thevenin equivalent circuit to find the current in RTH, give your answer in Amps with 3 significant digits. enter the number, no units. If necessary use scientific notation in the form 1200 = 1.20e3. R1 R4 R5 R3 R6

For the circuit below, Vs = 45V, R1 = 120, R2 = 30, R3 = 90, R4 = 320, R5 = 160, R6 = 3 With R4 as the load resistor use the Thevenin equivalent circuit to find the current in RTH, give your answer in Amps with 3 significant digits. enter the number, no units. If necessary use scientific notation in the form 1200 = 1.20e3. R1 R4 R5 R3 R6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

c) The following stiff voltage-divider circuit in Figure Q2 (c) consists of BJT with DC gain 140. Determine Q-point if Vcc= 12V, R1=15kO, R2 =5.6kn, RĘ =6000 and Rc=1.0kO. R, R. Vcc R2 RE ww ww w- ww
Q3
1. A voltage divider provides 1 V output from 5 V input. The maximum output current is 1 mA. The resistors are chosen to provide load regulation of better than 1% over the load current range of 0-1 mA. Find the resistor values necessary for this application. What is the efficiency at full load?
A balanced 3-0 star connected load is fed from a 350 V, 3-p supply. Each load has resistance of 35 Q. The total Active power is Select one: O a. 1.15Kw O b. 3500KW O C. 12KW O d. 3.5Kw
Design an analog circuit diagram to the following analog equation: V.= 0.35V1-5.24V2-4.5 Design an analog circuit diagram to the following analog equation: V. = -5V1+3.5V2+20V3+10
R, R. R, out R. R. out out 20kn Figure 3 Figure 1 Figure 2
4. Calculate vol and vo2 for the following op- amp circuit U1 vo1 +, V1 15V R1 ОРАМP 500 R2 U2 2k vo2 R5 + 5k V2 +. 10V R3 ОРАМP 400 R4 1k
How do we know that with amplification with emitter degenerate resistor amplifier both M1 and M2 are in the saturation region?
Question 4 Figure Q4a shows a basic current mirror structure (in its 'sink' form) which is designed to provide the current Ir at its output Io by operating transistors Ti and T2 identically : VDD IR IR T3 T1 T2 T1 T2 OV OV Figure Q4a : Current Mirror Figure Q4b : Widlaw Mirror a) Show that the current relationship of the circuit in figure Q4a is ( where Ic = BIb for both transistors and T1 and T2 are matched) : IR 2 =|1+ If the two transistors in figure Q4a are not matched in terms of b) their Vbe's compensation can be provided by placing a resistor 'R' in one of the emitter legs of the transistors. Assuming Vbez > Vbel by 0.05V and Ir = Io = 10mA sketch an appropriate structure and value for R. c) Describe how the 'offset' compensation referred to in Q4b occurs in practice for a 741 op-amp ? d) Sketch the 'Source' form of figure Q4a e) Figure Q4b shows the buffered Widlar mirror. Briefly describe how the addition of transistor T3 improves operation.
ans fast please
Simplify the circuit in Figure Q1(b) into a Thevenin circuit maintaining VA as output. 42 2V ЗА 160 Figure Q1(b)
Calculate the expression of the output resistance in terms of R in the circuit given below (hint: You can also find the resistance value by using one of the simulation methods. You can give the value instead of R and see the result on the screen.