Please answer number 1 and why is number 2 correct? Fornos. 1-5, consider a 2.4-m boom held by fixed support at C and supported by two cables AD and AE. The tension in cablesAD and AE are 325 N and 280 N, respectively.0.8 m0.8 m0.6 mB1.2 m1.2 m1.2 m1. Which of the following gives the moment about the y-axis of force TAE acting at A?288 N-m2. Which of the following gives the moment about point C of force TAD acting at A?(-180i-240j + 0k) N-m

Given data:- Tension in cable AD is 325 N Tension in cable AE is 280 N Below diagram is given in…

For nos. 1-5, consider a 2.4-m boom held by fixed support at C and supported by two cables AD and AE. The tension in cables AD and AE are 325 N and 280 N, respectively. 0.8m 0.8 m 0.6m 1.2 m 1.2m 1.2m 1. Which of the following gives the moment about the y-axis of force TA acting at A? 288 N-m + X 2. Which of the following gives the moment about point C of force TAD acting at A? (-180i-240j +0k) N-m +

For nos. 1-5, consider a 2.4-m boom held by fixed support at C and supported by two cables AD and AE. The tension in cables AD and AE are 325 N and 280 N, respectively. 0.8m 0.8 m 0.6m 1.2 m 1.2m 1.2m 1. Which of the following gives the moment about the y-axis of force TA acting at A? 288 N-m + X 2. Which of the following gives the moment about point C of force TAD acting at A? (-180i-240j +0k) N-m +

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the coordinates of the 60 mm Centroid of the shaded area shown 30 mm in item 3. 30 mm X 45…

Q: Can I have the answers in 3 decimal points

A: Therefore moment at the section

Q: What is the distance in miles from the principal meridian that describes Range 4 West? Select one: a…

Q: Problem No. 2: Determine the x and y-coordinate of the centroid of the shaded area.

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Y 50 1 1 150 50 Answers:…

A: To find out the X and Y coordinates of the centroid of the shaded area.

Q: Within some directives, there are choices limited to brackets [], meaning Automatic selection when…

A: There are several type of brackets used such as- { }, [ ], ( ), etc. All these brackets have…

Q: Q1/ Choose the correct answer (True or False) False O O True AutoCAD provides nine ways to draw an…

Q: I want theory part about flash and fire point with details

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 65 -190- 65 125 Dimensions in…

A: ASKED: To determine the x and y-coordinates of the centroid of the shaded area. The given shaded…

Q: Identify the portion of a foot (12") as indicated by the reading from the zero mark (0) on the scale…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Problem #3: Note: Replace all zero digits of your ID number by number "2" F1= 40 + A (N) Use X =…

Q: Q3. For the object shown, sketch a third-angle orthographic projection of the object showing all the…

Q: Differentiate Track from Field events.

A: The main difference is the way in which the events are conducted, and where they take place. For…

Q: Note: Replace all zero digits of your ID number by number "2" Problem #1: XN Use X Last 3 digits of…

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. -32 107…

A: The given figure is shown below:

Q: uO 9:1 * Asiacell lin. yols- i docs.google.com 14. Which is NOT a unit of length measurement? Yards…

A: 1.Hear in this question Grads are not units of linear measurements or length measurements, since…

Q: Given the fence 20 meters long and 3 meters high, determine the total number of pieces of 10 mm…

A: ASSUME SPACING OF VERTICAL BARS= 0.4 METER

Q: Write a short note on the software used for determining magnetic declination.

A: As we know, the earth has every complex shape of the earth magnetic field at the same place the…

Q: What do you mean by make-up airflow rate?

A: Air enters a building of the quantity nearing the exhaust flow rate whether or not provision is made…

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 30 --X 100…

Q: Problem #4: Note: Replace all zero digits of your ID number by number "2" A B P. Use X = Last 3…

Q: 1. Locate the centroid (£, 9) of the shaded area. 6 in. 3 in. 6 in. 6 in.

A: We are supposed to answer the only the first question, Kindly understand and post other question…

Q: Please

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 60 -145- 60 130 -x Dimensions…

A: To find location of centroid

Q: 7. Usually the minimum height in the room should not be lower than ( A. 2.2 m B. 2.0 m C. 2.4 m…

A: Note: Multiple questions are asked. Therefore, as per Bartleby guidelines, the answer of only…

Q: The following level notes were taken by students. Calculate the elevation of each station. Height of…

A: Calculate elevation of each station

Q: Hand Writing not allowed please provide Typed answer

A: The distance between v1 and v2 is √37 or approximately 6.08 units.Explanation:Formula for distance…

Q: Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide. The floor plan of Isobel and…

A: Scale can be defined as the ratio of the dimension in plan or map to the actual dimension Scale is…

Q: Note: Replace all zero digits of your ID number by number "2" Problem #2: 2 m W = X N Use X = Last 3…

Q: bulation gives elevations of points over the area of a 30m x 40m city lot. The elevations were…

A: Given:- area=30mx 40m To find:- Plotting contours

Q: Please recheck and answer in 3 decimal places.

Q: Two springs are used to support the steel truss structure of 2.5 m height shown in the figure. The…

A: Given: Spring 1: (right support) Shear modulus, G1=300+41=341 GPa Spring diameter, d1=20 mm Helical…

Q: 6. Why is it more advisable to use light colors in AutoCAD workspace? O Enter your answer

A: It is advisable to use the light colors in the workspace area of the AutoCAD.

Q: Need clear and complete solutions. Determine the coordinates of the centroid of the shaded area. 10…

A: Given data

Q: create a graph showing the value of the air density as a function of temperature. The Command Window…

A: The density of dry air can be expressed as a function of temperature and pressure.…

Concept explainers

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.

Question

Please answer number 1 and why is number 2 correct?

For
nos. 1-5, consider a 2.4-m boom held by fixed support at C and supported by two cables AD and AE. The tension in cables
AD and AE are 325 N and 280 N, respectively.
0.8 m
0.8 m
0.6 m
B
1.2 m
1.2 m
1.2 m
1. Which of the following gives the moment about the y-axis of force TAE acting at A?
288 N-m
2. Which of the following gives the moment about point C of force TAD acting at A?
(-180i-240j + 0k) N-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

B- What are the common sources of error associated with measurements?
Please verify if my answer is correct, if not, please indicate the correct one. Thank you!
ID NUMBER - 20-3994-175 *PLEASE ANSWER ALL THE QUESTIONS . Pls Put the number in every answer Don't Round Off answers unless it is already the final answer Final Answer must be up to 3 Decimal Places only
ID NUMBER- 20-3994-175 PLEASE ANSWER ALL THE QUESTION
MY ID NO. 20 -3994 -175 PLEASE INDICATE THE NUMBER IN EVERY ANSWER FINAL ANSWERS MUST BE UP TO 3 DECIMAL PLACES ONLY
Q11
Hi! Please me with this please. Thank you very much!
Q1/ Choose the correct answer (True or False) False O O True AutoCAD provides nine ways to draw an arc Line, Circle, Polyline, and Rectangle and so on and they are available in the modify panel of the ribbon AutoCAD is a CAD software package developed and marketed by Autodesk Inc AutoCAD measures the angle in counterclockwise direction The Rotate tool rotates an object or a group of objects about a base point
Please help me please ***Giotto's scrovegni chapel**** Where is this church located, how was it designed from the inside, and what does it say about its design in addition to the colors used?