Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide.  The floor plan of Isobel and Neliwe’s garage floor uses a scale of 1:25. Use this scale to determine the following: 1.4The floor plan length of the garage (in mm) if the actual length of the garage is 5400mm.   1.5The actual length of the window (in meters) if Isobel measures a window on the floor plan as 6,4 cm long.

Q: If you were to measure the cross section of a 2 x 4 you would find it to be 38 millimeters wideby 90…

A: Objective: To choose the correct option corresponding to size specifications of cross-section of a…

Q: A bedroom has a volume of 126 m3m3 . What is its volume in decimeters cubed (dm3dm3)?

A: Given data- The volume of the bedroom = 126 m3 To Find- The volume of the bedroom in decimeters…

Q: When two parallel lines are drawn at a distance of 50 mm for both sides of an angle, according to…

A: Given- An angle from the sides of which two parallel lines are drawn. Required- To find value of R.…

Q: Q4: Find the total area A of the shape below in Figure 3?

A: Given data- A semi-circle of radius 'r' as shown- To Find- The total area of the shape.

Q: Calculate the shape factor of the cross-section shown. 200 12 250 600 50 50 700

A:

Q: With respect to the given X & Y axis of the shaded section.

A:

Q: Determine the vertical distance H from the lower edge of the cross-section to the y coordinate of…

A: Given figure,

Q: This blueprint shows the layout for rectangular ducting for a home forced airheating system. The…

A: As per out rules and guidelines we solve only first three subparts kindly resubmit the remaining…

Q: rom the x direction, provide the front view, top view, and left-side view using the meter line.…

A: The Isometric Front View, side view, and Top view of above drawing is given Below:

Q: Suppose a problem tells you that the length of a gate is drawn to scale. The scale of the drawing is…

A: given scale of drawing=1:50 length of gate on paper =10cm we know that  scale of drawing=(dimension…

Q: Make a step by step procedure on how to determine area of irregular figures and or shape.

A: Some unusual features are made up of rectangular or square circles. The locations of those odd…

Q: Exercise 3: Identify the surfaces with the appropriate letter that would appear in the FRONT view,…

A:

Q: dimension is 23.6 cm. What is the actual dimension?

A:

Q: From the diagram shown, all dimensions are in millimeters. Find the length of side x. 89 00' 2,268…

A:

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

A:

Q: Looking at the x direction, provide the front view, top view, and right-side view using the meter…

A:

Q: 57.5 inches tall. The scale of the model is 1 inch :9 feet.

A: Given Data : 57.5 inches tall measurement        Scale as 1inch:9feet To Determine: 57.5 inches…

Q: Enumerate at least five different units of measurement that usually use at hom

A: There are many ways in which technology can help in this case. If you want to wake up early in the…

Q: Convert the equivalence scale 1 inch = 30 feet to a ratio scale.

A: Solution:- Scale:- The scale of the map is the ratio of a distance on the map to the corresponding…

Q: Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: Instructions :  To draw orthographic projections using third angle projection method, take the view…

Q: magine a house. Describe one-dimensional, two-dimensional, and three-dimensional parts or aspects of…

A: Let's break down the one-dimensional, two-dimensional, and three-dimensional aspects of a house and…

Q: - 4- पिक (17 b=260m- de-Sm h= 300m = 204N/m to 2onm M= <40kN b f=30kW

A: Given. Udl =20kn/m bending moment 40knm Point load 30kn Draw sfd bmd

Q: How

A: 1 and 1 actually is the ratio representation of slope.

Q: The sides of a rectangle are 42cm and 59cm. Find its diagonal? *

A: The given question comes under surveying subject of civil engineering, in the given question sides…

Q: Where does an extensometer or micrometer dial gauge used?

A: An extensometer is a high accuracy instrument developed especially for geologists or civil engineers…

Q: Given the following cross section , find the area of the cross section

A: Given Details of a cross section  Required  Area of cross section

Q: Describe a good rule of thumb for relating inches and centimeters?

A: For converting inches to centimeters, always remember inch is always bigger than centimeters.

Q: Find the centroid of the composite figure ABCDEF (in the image).

A:

Q: Describe one-dimensional, two-dimensional, and three-dimensional parts or aspects of a water tower.…

A: It is asked to 1. describe one-dimensional, two-dimensional, and three-dimensional parts or…

Q: 20 cm 2o cm 40 cm 40cm 20cm 80 cm

A:

Q: Figure 20-7 Questions 1-10. 44 8. 6 38 20 24 34 Ol 76 8 80 84 88 92 10 Match the dimensions…

A:

Q: Determine the following: 1. Height of the object 2. Width of the object 3. Depth of the object…

A: 1. Height of the object = 2 + 1.25 = 3.25 ( Hint : Measured from Front View) 2. Width of the object…

Q: I have only 1:500 scale on my ruler, but from the instructions we will used 1:1000 scale, how will i…

A:

Q: 150 25 40 185 25 75 50

A: To draw the front, top and side view of the given object. Given 3d object:

Q: 2. Find the location of x measured from the y axis. 4" 5" X

A:

Floor Plan Details

Floor plans are the scale drawings that show the interplay of rooms, spaces, and physical objects. They are an integral part of the house plan. They let you see how people will move around the room. Floor plans determine the suitability of space for its intended use, work through any potential issues, and redesign before moving on to more comprehensive planning or constructing phases. It shows the different alternatives and perspectives related to the location and dimension of rooms, windows, doors, kitchen and all other things as per the requirement by the user. Many consultants give their own floor plans as reference to the clients for a better idea and to develop good floor plans.