For each of the three simple circuit boards you will need to calculate the total resistance Reg for theentire circuit board by using the measured resistances of each of the resistors, and the equations givento you in the theory section. Then using the applied voltage of 2V, as the theoretical voltage Vth for theentire circuit board you can calculate the theoretical current, ith, for the entire circuit board.Table 1(Resistors in series)R(Q)31010100200Req10Ω1000200Ωiex(A)0.00740.00640.0680.00640.6500.00641.283Using the equations for resistors in series calculate the theoretical voltages, andcurrents for each of the resistors, and the entire circuit. Use the measured values of theresistance in your calculations. Then calculate the % errors. Show work.Vex(V)2.006ith(A)Vth(V) % Error i % Error V

Answered: Image /qna-images/answer/da8e4f46-94d0-4696-a3df-25588430d7e6.jpg

Answered: For each of the three simple circuit…

Similar questions

Needs Complete solution with 100 % accuracy. Don't use chat gpt or ai.
a). A circuit consist of five resistors connected as below, determine the effective resistance in the circuit. RI R2 Given that R1, R,Rs,RA and Rs are given respectively as 50, 25, 30, 60 and 70Q, what is the current in the circuit if the potential aeross the resistors is 24 V?
Inew A circuit with a resistance R = 73 Q is connected to a battery with potential difference across the terminals of AV = 8.5 V. Input an expression for the current passing through the circuit, I. What is the current in milliamps, mA? If the resistance of the circuit was increased by a factor of ten, Rnew = 10R, what is the new current in milliamps, mA?
In the circuit shown below, Vs = 60 V, R1 = 7 Q, R2 =10 V, R3 = 6 Q and R4 = 6 Q. The Thevenin equivalent of this circuit consists of a voltage source Vth and series resistance RTh. FInd Vth and Rth and hence determine the current that will flow through a 50 Q resistor connected between points A and B. Give your answer in Amps to three decimal places. RTh I R3 R2 TA Vs VTh B Next > < Previous R4 R1 That -A B
I need a labled schematic on paper of the circuit showing + and - terminals of the battery, the direction of any current flowing through the circuit, and any voltage drop across any resistors. I also need the form of the equations dealing with I, R (or 1/R), and V equations filled in with the appropriate numbers and answer with units for this problem. Problem: The same two resistors are connected in parallel to a voltage source. The voltage source (∆Vtot) is a 48-V source and the resistor values are 6.4 Ω (R1) and 3.9 Ω (R2). Determine the equivalent resistance of the circuit. Determine the current in the circuit. Determine the voltage drop across each individual resistor.
Joules Law allows us to compute the power in a simple electric circuit: P=I2R a) Use the equation above to find an equation relating (dP/dt), (dI/dt), (dR/dt), I and R. b) I have a circuit with a 400 ohm resistor. I increase the voltage at 20 Volts/s. When the voltage reaches 350 volts, how quickly is the Power in the circuit increasing? Include units in your answer. Note that 1 Watt is equivalent to 1 Volt2/ohm. Hint: you will need to use another equation relating voltage to current from the acticity in class.
Shown in the figure below is an electrical circuit containing three resistors and two batteries. R₁ www 4 R3 www I 10 + ww 13 Write down the Kirchhoff Junction equation and solve it for I, in terms of 12 and 13. Write the result here: 11 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. 0 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components 10V, R1, 4V, and R2. 0 => The resistors in the circuit have the following values: • R₁ = 22 R2=502 R3 = 132 Solve for all the following (some answers may be negative): 1₁ = 12 = 13 = Amperes Amperes Amperes NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like R1, R2, R3 and 11,12,13. Use numerical values of 10 and 4 for the voltages.
Consider the circuit in (Figure 1). Suppose that v₁ = 14 V, v2 = 5 V, and i = 5 mA. Figure i + 1 of 1 5 mA source is absorbing power. 5 V and 14 V sources are developing power. 5 V and 14 V sources are absorbing power. 5 mA source is developing power. All sources are absorbing power. O All sources are developing power. Submit Correct Part G Previous Answers What is the total power developed in the circuit if the polarity of the 14 V source is reversed? Express your answer to three significant figures and include the appropriate units. P= 25 Submit mW Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining
Help pls
An electric device draws 7.50 A at 240 V. Part A If the voltage drops by 11 % , what will be the current, assuming nothing else changes? Express your answer using two significant figures. ΑΣφ ? I = A Submit Request Answer Part B If the resistance of the device were reduced by 11 % , what current would be drawn at 240 V? Express your answer using two significant figures. ΑΣφ ? I = A Submit Request Answer Drovid.
I need a labled schematic on paper of the circuit showing + and - terminals of the battery, the direction of any current flowing through the circuit, and any voltage drop across any resistors. I also need the form of the equations dealing with I, R (or 1/R), and V equations filled in with the appropriate numbers and answer with units for this problem. Problem: Two resistances are connected in series to a voltage source. The voltage source (∆Vtot) is a 48-V source and the resister values are 6.4 Ω (R1) and 3.9 Ω (R2). Determine the equivalent resistance of the circuit. Determine the current in the circuit. Determine the voltage drop across each individual resistor.
I need answer asap

SEE MORE QUESTIONS