For an AM superheterodyne receiver, station A with RF signal of 1000 kHz uses high side injection to receive the signal. A tuned circuit for a bandpass filter has inductor coil, L= 25 µH, resistor, R = 20 Q and capacitor, C = 4.894 nF. (i) Determine the center frequency of the bandpass filter. (ii) Determine the quality factor of the tuned circuit. (iii) Determine the bandwidth of the bandpass filter. (iv) Find the upper and lower cut frequency for the bandpass filter. (v) Plot the 3 dB bandwidth of the bandpass filter.

For an AM superheterodyne receiver, station A with RF signal of 1000 kHz uses high side injection to receive the signal. A tuned circuit for a bandpass filter has inductor coil, L= 25 µH, resistor, R = 20 Q and capacitor, C = 4.894 nF. (i) Determine the center frequency of the bandpass filter. (ii) Determine the quality factor of the tuned circuit. (iii) Determine the bandwidth of the bandpass filter. (iv) Find the upper and lower cut frequency for the bandpass filter. (v) Plot the 3 dB bandwidth of the bandpass filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For single-sideband production in AM SSBSC, three transmitter configurations are typically used: the filter approach, the phase-shift method, and the so-called third method. A bandpass filter circuit is used in the filter method to reject one sideband and transmit the remaining sideband. The modulating signal and carrier are applied directly to one of the modulators in the phase-shift method, then both are moved 90 degrees and applied to the second modulator. The outputs of the two balanced modulators are double-sideband suppressed-carrier signals with the proper phase, so that one of the sidebands is canceled when they are combined in a linear summer. The disadvantage of single-sideband transmission is which of the following statements? Select your answer. Tuning single-sideband receivers is more difficult and precise than tuning DSBSC AM receivers. Because most single-sideband transmissions involve a suppressed carrier, envelope detection cannot be employed unless the carrier is…
Spectra quality in ATR-FTIR is dependent on sample material. True False
1. Derive the lower cut-off frequency for the basic RC high-pass circuit in Figure 1. R, Figure 1.
PARTICULAR CONCEPT AND EXAMPLES OF : 1. Random Processes.1.2. Spectral characteristics.1.2.1. Power density spectrum.1.2.2. Definitions of noise
all 4
A receiver is invented by US engineer Edwin Armstrong, which it converts high frequency to low frequency, all processing takes place at lower frequencies. It offers superior sensitivity, frequency stability and selectivity. With neat block diagram and explain each blocks.
Q1): Use the PCM method to convert the signal below into a digital signal by assuming fm = 1000 Hz and n- 3. 4 -5 0.5 1 1.5 2.5 3 3.5 4 4.5 5 Time(ms) Q2): Use the DPCM method to: 1. convert the signal below into a digital signal by assuming fm = 500 Hz and n = 3. 2. reconstruct discrete signal at the receiver end. 3. calculate the error between the sampled discrete signal at transmitter end and the reconstructed discrete signal at the receiver end. 3 2 -2 3 2 3 4 5 10 1, (HOA) apnadury Amplitude (volt)
5. According to the relationship between matching filter transmission function and input determination signal in white noise background, briefly describe the principle of matching filter in white noise background ; briefly describe the reason why the matching filter is adaptive for signals with similar waveform but different amplitude and delay parameters.
2 short question related to communication lesson.
A discrete-spectrum baseband modulating signal has com- ponents at the following frequencies: 500 Hz, 1.5 kHz, 6-3