In the circuit given below, Rc= 5KQ, RE= 4 KO, RL=10KQ, Rsig= 5KN, assume IC=IE= 1mA &B= 100. If vsig is a small signal sine wave determine Avo, Gv, Rin. VCC Rsig VEE Avo= -133.3, Gv=-131.69 , Rin= 406.4KQ Avo= -200, Gv=-44.43, Rin=2.5KO Avo= -200, Gv=-131.69, Rin= 406.4KO Windows bu b sy I Avo= -133.3, Gv=-44.43, Rin= 2.5KO iull lis sI Bb acer N 图

In the circuit given below, Rc= 5KQ, RE= 4 KO, RL=10KQ, Rsig= 5KN, assume IC=IE= 1mA &B= 100. If vsig is a small signal sine wave determine Avo, Gv, Rin. VCC Rsig VEE Avo= -133.3, Gv=-131.69 , Rin= 406.4KQ Avo= -200, Gv=-44.43, Rin=2.5KO Avo= -200, Gv=-131.69, Rin= 406.4KO Windows bu b sy I Avo= -133.3, Gv=-44.43, Rin= 2.5KO iull lis sI Bb acer N 图

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the resonant angular frequency, Q value, and half width of the resonant circuit in the figure. (If possible, please show the all the detail work on paper so i can understand:) )
The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
For the signal and circuit below, determine the maximum frequency that may be used. Op-amp slew rate is SR = 0.9 V/us. Refer to the image for the circuit, but refer to the following for the given values: Rf = 323996 ohms, Ri = 14089 ohms, Vi = 0.03 C, and w = 404604 x 10^3 rad/s. Express your answer in 10^6 rad/s, no units required, round-off up to two decimal places.
Design with IC ‘555 and a capacitor of 9 uF: Monostable to get signal period=7 Astable to get frequency=2 Constraints: Use any resistor to be between 1K and 50K.
Information: 2 Vp-p (Am = 1V) 20 Hz sine waveCarrier: 4 Vp-p (Ac = 2V) 500 Hz sine waveModulation Index: ma = 1DC offset: 0V ma=Acmax-Acmin/Acmax+Acmin for the modulated signal (AM) ,ma = 1;Calculate Acmax, Acmin and efficiency value.
Determine the Nyquist sampling rate and the Nyquist sampling interval for the signals: (b) sinc² (10071) (c) sinc (10071) + sinc (50r t)
2. In each case, what will be the frequency in the square wave and the sampling rate you will choose in your experiment? 3. Sketch the voltages on R and C for 2 period of the square wave, label your time axis with value and unit. 4. repeat step 4 for RL circuit.
Q2- Explain by equations and block diagram the direct method demodulation in NBFM Q3- Write the formula of the phase modulation (PM) when Ac=25 , Fc=10® Hz, Kp= 20 . If an information signal m(t) = cos(212000t) + 10sin(2n2000t) Q4- Drive a formula for NBFM by using Bessel function Q5- If an information signal X(t) = cos(2n700t) + 10cos(25000t). Write the formula of the frequency modulation (FM) when Ac=20 , Fc=10® Hz, Kf= n2000 Q6-) If NBFM signal passes through a frequency multiplier. With B < 0.5 and fc=200kHz. Let fm ranges from 50OHZ to 15kHz, and let the maximum frequency deviation Afat the output be 75kHz. Find the required frequency multiplication n and the maximum allowed frequency deviation at the input. Q7- If an angle modulated signal S(t) = 10[cos(210®t) + 15sin(2n10³t)]
1. Derive the lower cut-off frequency for the basic RC high-pass circuit in Figure 1. R, Figure 1.
In the filter shown in figure 8 the ratio between the output AC voltage Vout and input voltage Vin is given by Vout R wCR (1) R+ j(wL – 1/(wC)) Vin R+ j(w?LC – 1) - -
Q4: a) A In center tape FWR circuit ,R=9002,V,=150Volt ,f=60H .Draw output wave form, then find Vac,VPIV.
Consider the design of a low frequency differentiator to achieve the differentiation gain K = 0.001, and the highest frequency of the input signal is fH = 1000HZ. Determine the value of Ri, and Rf based on the criterion fb = 10fH.Assume that capacitor value is C = 0.1uF Ri= Rf= Ohms Kilo Ohms